1982/01/11 Caterpillar


Use FT1555 Generator Rotor Removal Tool To Remove And Install Rotor Assembly{0626,0644,0665,4457}

Usage:


SR4 Generators

A new FT1555 Generator Rotor Removal Tool (see the illustration) is available for use on SR4 Generators which are used with large engines such as the D379, D398, D399, 3412 and 3500 Series Engines. The lifting tool is used to remove and install the rotor assembly.

The FT1555 Generator Rotor Removal Tool makes it easier to remove and install the rotor assembly. Also, correct use of the tool prevents possible damage to the stator and windings on the rotor assembly.

Make reference to the Service Manual, Form No. SENR7958 for correct use of this tool.

Drawings for the FT1555 Generator Rotor Removal Tool are available from your Division Service Manager.


FT1555 Generator Rotor Removal Tool.

Caterpillar Information System:

1982/01/11 "Sirs User Instructions" Available{0374}
1982/01/11 Procedure Reduces Possibility Of Spraying Hot Hydraulic Oil When S.O.S. Sample Is Taken{0372,5068}
1982/01/11 Improved Head Gasket Has Larger Fire Ring To Decrease Fretting{1101,1201}
1982/01/11 Check 14 Test Points In Less Than 5 Minutes With The 6V2150 Starting/Charging Analyzer Group{0651,1518,1406}
1981/12/21 Use Of A Flex-Hone For Cylinder Liner Reconditioning{0664,0674,1216}
1981/12/21 Shorter Bolt Gives Clearance For Wiper Motor Linkage{7305,7300}
1981/12/14 New Cylinder Liners And O-Ring Seals Give Longer Seal Life{1216,1201,1213,1227}
1981/12/14 New Springs For Timing Advance Used In Governor And Fuel Pump Drive Group{1272,1288}
1981/12/14 How To Remove The 7L4511 Sleeve Assembly From Aftercoolers{0620,1063}
1981/12/14 New Oil Level Gauge Used To Prevent Vibration{1300,1318,7450}
1981/12/14 New Flywheel Housing Gasket Used{1201,1157}
1981/12/14 6V4111 Adapters Available To Pull Spoke-Type Sprockets{4164,0623}
1982/01/18 New Lever And Improved Link Used To Permit Full Movement Of Articulation Indicator{7476}
1982/01/18 New Adjustment Dimension For Master Cylinder Rod{4111}
1982/01/18 Coasting While In Neutral Causes Transmission Damage{3150,3176}
1982/01/18 Communicate With Photography{0336,7750}
1982/01/18 Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18 Larger Diameter Heater Control Shaft Gives Better Performance{7304}
1982/01/18 New Torque Specification For Bushing{0374,1253,1251}
1982/01/18 Ground Wire Added To Coolant Flow Switch For Positive Operation Of Alarm{1408,1350,7400}
1982/01/25 New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group{0622,1217}
1982/01/25 New Washers Permit Locks To Hold Better{1252}
1982/01/25 Use The New 6V4186 Timing Pin{0654,1250}
1982/01/25 Air Lines Group And Turbocharger Group Changed To Improve Connections{1058,1052,1063}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.