Wheel Spindle and Wheel Spindle Housing - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1A-5666 | Full Nut | 1 |
B | 439-3941 | Link Bracket As | 2 |
1U-9199 | Lever Puller Hoist | 1 | |
C | 5P-4197 | Spacer | 1 |
3H-0459 | Stud | 1 | |
316-1493 | Hydraulic Puller As | 1 | |
439-5246 | Pump As | 1 | |
D | 1P-0510 | Driver Gp | 1 |
E | 1P-1833 | Bearing Puller Adapter | 1 |
5P-4776 | Tool Stud | 1 | |
9U-6833 | Nut | 1 | |
9U-6250 | Pump Tool Gp | 1 | |
4K-0684 | Hard Washer | 1 | |
316-1493 | Hydraulic Puller As | 1 |
Start By:
- Remove the front wheel and tire.
Show/hide table
When you are using hydraulic cylinders and puller studs, always ensure that the rated capacity of the puller stud meets or exceeds the rated capacity of the hydraulic cylinder. If the puller stud does not meet or exceed the rated capacity of the hydraulic cylinder, a sudden failure of the puller stud could occur. The sudden failure of the puller stud could result in personal injury or death. |
- Remove cotter pin (1) and nut (2). Install Tooling (A) and strike with a hammer to break the taper.
- Position steering link assembly (3) out of the way.
Show/hide table
Illustration 2 g01021808 - Remove bolt (4), bolt (6), and washer (5).
Show/hide table
Illustration 3 g01021810 - Remove cotter pin (7) and nut (8). Install Tooling (A) and strike with a hammer to break the taper.
- Position cylinder group (9) out of the way.
Show/hide table
Illustration 4 g01021811 - Attach Tooling (B) and a suitable lifting device to wheel spindle (10). The weight of wheel spindle (10) is approximately
90 kg (198 lb) . - Use Tooling (C) to remove pin (11).
Show/hide table
Illustration 5 g01021813 - Use Tooling (C) to remove pin (12).
Show/hide table
Illustration 6 g01021815 - Remove wheel spindle (10).
- Remove two seals (14) and two O-ring seals (15).
- Remove ring (13) from pin (12), and ring (16) from pin (11).
Show/hide table
Illustration 7 g01021934 - Remove thrust washers (17) and seal (18).
Show/hide table
Illustration 8 g01021827 - Use Tooling (D) to remove two bearings (19).
Show/hide table
Illustration 1 | g01021806 |
- Lower the temperature of bearings (19). Use Tooling (E) to install bearings (19).
Show/hide table
Illustration 10 g01021934 - Install thrust washers (17) and seal (18).
Show/hide table
Illustration 11 g01021815 - Lower the temperature of pins (11) and (12).
- Install O-ring seals (15) and seals (14).
- Install wheel spindle (10).
- Install pins (11) and (12). Install rings (13) and (16). Pins (11) and (12) must protrude to the dimension of
2.0 ± 0.5 mm (0.08 ± 0.02 inch) .Show/hide tableIllustration 12 g01021810 - Position cylinder group (9).
- Install nut (8) and tighten to a torque of
140 ± 14 N·m (103 ± 10 lb ft) . Install cotter pin (7).Show/hide tableIllustration 13 g01021808 - Install washer (5) and bolt (4). Install bolt (6).
Show/hide table
Illustration 14 g01021806 - Position steering link assembly (3).
- Install nut (2) and tighten to a torque of
120 N·m (89 lb ft) .
Show/hide table
Illustration 9 | g01021911 |
End By:
- Install the front wheel and tire.
Caterpillar Information System:
An Improved Pump Drive is Now Used on Certain 794 AC, 795 AC, and 797F Off-Highway Trucks {3108} An Improved Pump Drive is Now Used on Certain 794 AC, 795 AC, and 797F Off-Highway Trucks {3108}
797F and 797F XQ Off-Highway Trucks Cable (Truck Body Retaining)
A Planetary Group Lock Ring May Loosen on Certain 797, 797B, and 797F Off-Highway Trucks {3030, 3160} A Planetary Group Lock Ring May Loosen on Certain 797, 797B, and 797F Off-Highway Trucks {3030, 3160}
New Rocker Arms Are Used on Certain C27 and C32 Engines {1123} New Rocker Arms Are Used on Certain C27 and C32 Engines {1123}
140 Motor Grader Power Train Transmission Oil Filter Base - Remove and Install
New Monitor Software Is Now Used for Certain 140 Motor Graders {7610, 7620} New Monitor Software Is Now Used for Certain 140 Motor Graders {7610, 7620}
336, 336 GC and 340 Excavator Systems Drain Line
Door Lock Assemblies May Fail on Certain 320 to 345 GC Excavators {7273} Door Lock Assemblies May Fail on Certain 320 to 345 GC Excavators {7273}
Procedure to be Performed on C175 Commercial Engines {1239} Procedure to be Performed on C175 Commercial Engines {1239}
140 Motor Grader Power Train Wheel and Tire (Front) - Remove and Install
3500 Engines Air Regulator - Assemble
140 Motor Grader Power Train Gear Group (All Wheel Drive) - Remove and Install
Incompatible Coolant Pressure Sensor Identified on Certain 3512E and 3516E Engines {191W} Incompatible Coolant Pressure Sensor Identified on Certain 3512E and 3516E Engines {191W}
The Hoist Cylinder Head is Improved on Certain 797 Off-Highway Trucks {5102} The Hoist Cylinder Head is Improved on Certain 797 Off-Highway Trucks {5102}
New Enclosure Parts Are Now Available for 336, 336GC, and 345GC NGH Excavators {7251, 7276} New Enclosure Parts Are Now Available for 336, 336GC, and 345GC NGH Excavators {7251, 7276}
Operator Seat Belt Not Retracting {7327} Operator Seat Belt Not Retracting {7327}
The Main Hydraulic Pump May Leak Oil From Shaft On Certain 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavators {5070} The Main Hydraulic Pump May Leak Oil From Shaft On Certain 301.7 CR, 301.8, and 302 CR Mini Hydraulic Excavators {5070}
Procedure to Install Auxiliary Lines on Certain Mini Hydraulic Excavators {5051, 5063, 5462} Procedure to Install Auxiliary Lines on Certain Mini Hydraulic Excavators {5051, 5063, 5462}
Head Gasket May Fail On Certain Cat® Products {1100} Head Gasket May Fail On Certain Cat® Products {1100}
320 GC, 320 and 323 Excavator Machine Systems Specifications Fuel Lines
Certain Generator Set Labels May Not Match With Technical Marketing Information (TMI) Data {7405, 7557} Certain Generator Set Labels May Not Match With Technical Marketing Information (TMI) Data {7405, 7557}
320 GC, 320 and 323 Excavator Machine Systems Specifications Hood - Engine Hood
Correct Product ID is Now Being Set on Cat® Product Link Devices (Telematics Boxes) Used on Machines Programmed From the Factory {7606} Correct Product ID is Now Being Set on Cat® Product Link Devices (Telematics Boxes) Used on Machines Programmed From the Factory {7606}
320 GC, 320 and 323 Excavator Machine Systems Specifications Fuel Filter Mounting