Cylinder Block
Show/hide table
| |
| Illustration 1 | g06148718 |
|
Front view | |
Show/hide table
| Specification for 383-7225 Cylinder Block Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| A | 32 | 8T-0099 Dowel | Extension of the dowel from the top face of the cylinder block is |
| 1 | 2 | 4W-4813 Plug | Torque to |
| 2 | 1 | 350-1417 Cylinder Block | During assembly, top of cylinder block must be free of fuel, oil, water, gasket adhesives, assembly compounds, and any other contaminants. |
| 3 | 18 | 116-1359 Camshaft Bearing | All centerlines through oil holes in the camshaft bearings and the camshaft bearing junctions must be positioned that is shown in Illustration 1 for each side of the cylinder block. |
| B | 16 | 197-7008 Dowel | Extension of the dowel from the top face of the cylinder block is |
| C | - | - | Bore in the cylinder block for the camshaft bearings is |
| D | - | - | Oil holes in the camshaft bearings must be positioned from the horizontal centerlines at an angle of 20 ± 5 degrees. Refer to Illustration 1. |
| E | - | - | New dimension from centerline of crankshaft bearing bore to bottom of block (pan rails) is |
| F | - | - | Bore in the block for the main bearings is |
Show/hide table
| |
| Illustration 2 | g06148736 |
|
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| G | 3 | 7N-2047 Dowel | Extension of the dowel from the front face of the cylinder block is |
| H | 2 | 4N-0683 Dowel | Extension of dowels from the rear face of the cylinder block is |
| J | 2 | 7N-2044 Dowel | Extension of dowels from the front face of the cylinder block is |
Show/hide table
| |
| Illustration 3 | g06148738 |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 4 | 16 | 352-6061 Liner Seal | Assemble liner seals dry on clean and dry liner grooves.
Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 5 | 48 | 7N-2046 O-Ring Seal | Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| K | - | - | Width in the cylinder block for crankshaft bearing cap is |
| L | - | - | New dimension from centerline of crankshaft bearing bore to the top of the block is |
| 6 | 9 | 223-1696 Crankshaft Bearing Cap | Width of the crankshaft bearing cap is |
| 7 | 36 | 7X-7925 Bolt | Use the following procedure to tighten the crankshaft bearing cap bolts: Install main bearing caps with the cast part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail. 1. Before assembly, lubricate the threads completely with clean engine oil. 2. Hand tighten bolts in the tapped holes. 3. Tighten bolts in the numerical sequence as shown in Illustration 3 to 4. Again, tighten each bolt to an extra angle of 180 ± 5 degrees. |
Caterpillar Information System:
G3500J Petroleum Engines Cylinder Head
G3500J Petroleum Engines Camshaft
C15 and C18 Engines for Caterpillar Built Machines Alternator Mounting
New Speed Sensor Groups Are Now Used on Certain Machine Engines {1907, 1912, 3141, 3175, 4803, 7493} New Speed Sensor Groups Are Now Used on Certain Machine Engines {1907, 1912, 3141, 3175, 4803, 7493}
New Speed Sensor Groups Are Now Used on Certain C13, C32, C280, 3176B, 3400E, G3400, 3500, G3500, and G3600 Engines {1907, 1912, 3141, 3175} New Speed Sensor Groups Are Now Used on Certain C13, C32, C280, 3176B, 3400E, G3400, 3500, G3500, and G3600 Engines {1907, 1912, 3141, 3175}
Radiator Fan Shaft Bearing Set Screw Inspection and Installation {1353, 1356} Radiator Fan Shaft Bearing Set Screw Inspection and Installation {1353, 1356}
C175-16 Locomotive Engine Diesel Exhaust Fluid System - Inspect
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Clean Emissions Module Support - Inspect
G3516 Engines Engine Design
G3500J Petroleum Engines Air Lines
G3512 Gas Engine Engine Oil Lines
G3500J Petroleum Engines Fuel Lines
G3516 Engines Connecting Rod
G3500J Petroleum Engines Turbocharger
CN1566, CN2086, CN2586, CN3086, CN3586, CN4086 and CN5086 Electric Motors Rotor - Rotate - Motors with Anti-Friction Bearings
CN1566, CN2086, CN2586, CN3086, CN3586, CN4086 and CN5086 Electric Motors Rotor - Rotate - Motors with Sleeve Bearings
C32 Marine Propulsion Engine Maintenance Interval Schedule
G3516 Engines Exhaust Bypass Valve
G3500J Petroleum Engines Air Inlet Elbow
G3516 Engines Housing (Front)
C32 Marine Auxiliary Engine Safety Messages
C32 Marine Auxiliary Engine Model View Illustrations
Exhaust Back Pressure Valve on Certain C7.1 Engines {108N} Exhaust Back Pressure Valve on Certain C7.1 Engines {108N}
C32 Marine Auxiliary Engine Product Description