Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
Note: Every 9000hrs or 3 years, using ULSD Fuel.
Show/hide table
Illustration 1 | g06139651 |
Note: During installation, inspection, and handling of the sensor, follow the parameters listed below:
Note: Turn off power supply before disconnecting or connecting the NOx sensor.
- Inspect harness for damaged wiring
- Inspect for secure connections at all ends of the harness
- Do not contact the sensing element when power is applied to the sensor. Contact with the sensing element may result in injury. The sensing element is heated to a minimum of
100° C (212° F) . - Do not use any lubricant on any part of the sensor other than the threads. Do not use unapproved thread lubricant. Do not apply additional anti-seize to new parts. If additional anti-seize is necessary for pre-installation, use only nickel based anti-seize or non-metallic anti-seize. Apply anti-seize to the threads only and avoid contaminating the sensor head.
- Do not use sensors that have been dropped or have been exposed to other forms of mishandling. Damage to the sensor may have occurred that is not visible.
- Replace the sensor if damaged or faulty.
To replace the NOx sensor, follow the steps listed below:
- Disconnect harness assembly and disconnect sensor cabling.
- Use 468-8116 Slotted Socket (22mm) to loosen the sensor.
- Remove NOx sensor probe.
Show/hide table
Illustration 2 g02715050 - Install outlet NOx sensor probe. Take precautions to prevent damaging the ceramic sensor element (4) when installing.
- Ensure that the sensor is securely mounted.
- Connect harness assembly and cabling.
- Install cover plate assemblies and bolts. Refer to Specifications, SENR3130, "Torque Specifications" for the proper torque.
Caterpillar Information System:
G3516 TA Engine Engine Monitoring System
SCR Retrofit Aftertreatment Exhaust Inlet Nitrogen Oxide Sensor - Inspect/Replace
Installing Coolant Tubes and Clamps on Certain C175-16 Locomotive Engines {1307, 1380} Installing Coolant Tubes and Clamps on Certain C175-16 Locomotive Engines {1307, 1380}
G3516 TA Engine Electronic Service Tools
3500 Industrial and Generator Set Engines Engine Operation
G3500H 60Hz Generator Sets Jacket Water Heater - Check
A New Closed Crankcase Ventilation Drain Hose and Check Valve Are Now Used on Certain C18 Marine Separate Circuit Aftercooler Engines {1317} A New Closed Crankcase Ventilation Drain Hose and Check Valve Are Now Used on Certain C18 Marine Separate Circuit Aftercooler Engines {1317}
New Software Is Now Used For Certain 3516C Series Engines {1920} New Software Is Now Used For Certain 3516C Series Engines {1920}
G3500H 50Hz Generator Sets Engine Air Cleaner Element - Replace
323F SA Excavator and 323F MHPU Machine Systems Cylinder Drift - Check - Empty Bucket
A New Fuel Return Lines Are Used On Certain C18 Marine Engines {1274} A New Fuel Return Lines Are Used On Certain C18 Marine Engines {1274}
Marine Selective Catalytic Reduction (SCR) Retrofit Aftertreatment Diesel Exhaust Fluid Pump - Replace
A New Relay Is Now Used for Certain 3500 and C175 Tier 4 Urea Dosing Cabinets {7451, 7490} A New Relay Is Now Used for Certain 3500 and C175 Tier 4 Urea Dosing Cabinets {7451, 7490}
G3500H Generator Set Engine Electronic Control System Parameters - Configuration Parameters
A New Piston Ring Compressor Tool Is Now Available For All 3500B And 3500CCommercial And Machine Diesel Engines That Use Cuff Liners {0701, 1000} A New Piston Ring Compressor Tool Is Now Available For All 3500B And 3500CCommercial And Machine Diesel Engines That Use Cuff Liners {0701, 1000}
C7.1 Marine Engine Fuel Injector - Remove
C7.1 Marine Engine Fuel Injector - Install
The Electrical Guard is Missing on Certain C32 Engines {7274} The Electrical Guard is Missing on Certain C32 Engines {7274}
C175 Oil&Gas Offshore Engine Electronic Control Module (ECM)
C175 Oil&Gas Offshore Engine Lubrication System Operation
G3500H 50Hz Generator Sets Space Heater - Test
The Main Rotor Lead Wires and/or Terminal Lugs May Become Loose and/or Break on Certain C32 Generator Sets {4456, 4457, 4460} The Main Rotor Lead Wires and/or Terminal Lugs May Become Loose and/or Break on Certain C32 Generator Sets {4456, 4457, 4460}
C175 Oil&Gas Offshore Engine Centrifugal Oil Filters
C175 Oil&Gas Offshore Engine General Information (Air/Electric Starting System)