Crankshaft Front Seal - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-7600 | Slide Hammer Puller | 1 |
B | 5P-1733 | Seal Locator | 1 |
C | 5P-1737 | Bolt | 3 |
D | 9S-8858 | Nut (Seal Installer) | 1 |
E | 6V-6142 | Seal Installer | 1 |
Start By:
- Remove the vibration damper and the pulley.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- If necessary, use Tooling (A) or a punch and hammer to puncture three or more holes in wear sleeve (1).
- If necessary, use Tooling (A) to remove wear sleeve (1).
- Use Tooling (A) or a punch and hammer to puncture three or more holes in crankshaft front seal (2).
- Use Tooling (A) to remove crankshaft front seal (2).
Show/hide table
Illustration 1 | g01255652 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth to remove any imperfections on the crankshaft.
- Clean the outside diameter of the crankshaft.
Show/hide table
Illustration 2 g01255654 - Use Tooling (C) to attach Tooling (B) to the crankshaft.
Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft rotation toward the front of the engine.
- Position wear sleeve (2) and crankshaft front seal (1) as a unit on Tooling (B). Install Tooling (E) on Tooling (B). Lubricate the face of the washer on Tooling (D). Install Tooling (D) on Tooling (B).
- Tighten Tooling (D) until Tooling (E) contacts Tooling (B).
- Remove Tooling (D) and Tooling (E) from Tooling (B).
- Remove Tooling (C) and Tooling (B) from the crankshaft.
Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the wear sleeve.
End By:
- Install the vibration damper and the pulley.
Caterpillar Information System:
3512E Land Electric Drive Engine Air Cleaner Differential Pressure - Check
Reusability Inspection of Well Stimulation Pump Crankshaft {1202, 5070, 6002} Reusability Inspection of Well Stimulation Pump Crankshaft {1202, 5070, 6002}
TR35 Railway Transmission Output Transfer Gears - Adjust
3512E Land Electric Drive Fuel Conservation Practices
3512E Land Electric Drive Engine Operation
3512E Land Electric Drive After Starting Engine
3512E Land Electric Drive Starting with Jump Start Cables
3512E Land Electric Drive Starting the Engine
3512E Land Electric Drive Cold Weather Starting
TR35 Railway Transmission Transmission Pressures - Test and Adjust
3512E Land Electric Drive Reference Information
XQP500 Generator Sets Generator Lead Connections
C18 Generator Set Engines Front Cover - Remove and Install
TR35 Railway Transmission Transmission Oil - Change
3512C and 3516C Marine Auxiliary and Generator Set Engines Belts - Inspect/Adjust/Replace
TR35 Railway Transmission Transmission Oil Level - Check
TR35 Railway Transmission Transmission Oil Sample - Obtain
C175-20 Locomotive Engine Diesel Exhaust Fluid Pump - Inspect/Test
Hose Inspection Form {0374, 0599, 5057, 5057} Hose Inspection Form {0374, 0599, 5057, 5057}
TR35 Railway Transmission Transmission Oil Filter - Replace
TR35 Railway Transmission Maintenance Interval Schedule
XQP150 Rental Generator Set Walk-Around Inspection
XQP1100 Generator Set Engine Valve Lash - Check
A New Fuel Priming Pump Is Used On Certain C175-16 Locomotive Engines {1258} A New Fuel Priming Pump Is Used On Certain C175-16 Locomotive Engines {1258}