Maintenance Interval Schedule - Prime
Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.
Battery - Replace
Battery or Battery Cable - Disconnect
Circuit Breakers - Reset
Coolant Extender (ELC) - Add
Engine - Clean
Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Generator - Dry
Generator Set - Test
Generator Set Alignment - Check
Electrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Generator Load - Check
Jacket Water Heater - Check
Power Factor - Check
Voltage and Frequency - Check
Walk-Around Inspection
Battery Charger - Check
Generator - Inspect
Generator Bearing Temperature - Test/Record
Generator Lead (Flat Braided Cable) - Check
Engine Oil Sample - Obtain
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Oil and Filter - Change
Engine Protective Devices - Check
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Generator Lead (Round Cable) - Check
Generator Set Vibration - Inspect
Radiator - Clean
Stator Lead - Check
Engine Performance - Test
Rotating Rectifier - Check
Crankshaft Vibration Damper - Inspect
Electronic Unit Injector - Check/Replace
Engine Mounts - Inspect
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Starting Motor - Inspect
Turbocharger - Inspect
Water Pump - Inspect
Coolant Temperature Regulator - Replace
The user is responsible for the performance of maintenance, including all adjustments, the use of proper lubricants, fluids, filters, and the replacement of components due to normal wear and aging. Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.
Use mileage, fuel consumption, service hours, or calendar time, WHICH EVER OCCURS FIRST, in order to determine the maintenance intervals. Products that operate in severe operating conditions may require more frequent maintenance.
Note: Before each consecutive interval is performed, all maintenance from the previous interval must be performed.
When Required
Battery - RecycleBattery - Replace
Battery or Battery Cable - Disconnect
Circuit Breakers - Reset
Coolant Extender (ELC) - Add
Engine - Clean
Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Generator - Dry
Generator Set - Test
Generator Set Alignment - Check
Daily
Coolant Level - CheckElectrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Generator Load - Check
Jacket Water Heater - Check
Power Factor - Check
Voltage and Frequency - Check
Walk-Around Inspection
Initial 20 to 40 Service Hours
Belts - Inspect/Adjust/ReplaceEvery Week
Automatic Start/Stop - InspectBattery Charger - Check
Generator - Inspect
Generator Bearing Temperature - Test/Record
Generator Lead (Flat Braided Cable) - Check
Initial 250 Service Hours
Engine Valve Rotators - InspectEvery 250 Service Hours
Coolant Sample (Level 1) - ObtainEvery 250 Service Hours or 6 Months
Battery Electrolyte Level - CheckEngine Oil Sample - Obtain
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Every 500 Service Hours or 1 Year
Belts - Inspect/Adjust/ReplaceCooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Oil and Filter - Change
Engine Protective Devices - Check
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Every 2000 Service Hours or 1 Year
Engine Crankcase Breather - CleanGenerator Lead (Round Cable) - Check
Generator Set Vibration - Inspect
Radiator - Clean
Stator Lead - Check
Every Year
Coolant Sample (Level 2) - ObtainEngine Performance - Test
Rotating Rectifier - Check
Every 3000 Service Hours or 3 Years
Alternator - InspectCrankshaft Vibration Damper - Inspect
Electronic Unit Injector - Check/Replace
Engine Mounts - Inspect
Engine Valve Lash - Check
Engine Valve Rotators - Inspect
Starting Motor - Inspect
Turbocharger - Inspect
Water Pump - Inspect
Every 4000 Service Hours or 2 Years
Coolant (DEAC) - ChangeCoolant Temperature Regulator - Replace
Every 4500 Service Hours
Generator Bearing - LubricateEvery 12 000 Service Hours or 6 Years
Coolant (ELC) - ChangeOverhaul
Overhaul ConsiderationsCaterpillar Information System:
120 and 120 AWD Motor Grader Service Interval Chart
G3500H 50Hz Generator Sets Maintenance Interval Schedule
120 and 120 AWD Motor Grader Access Doors and Covers
120 and 120 AWD Motor Grader Tire Shipping Pressure
120 and 120 AWD Motor Grader Engine Starting with Auxiliary Start Receptacle
Autonomy Log Processing Setup {7008, 7605} Autonomy Log Processing Setup {7008, 7605}
120 and 120 AWD Motor Grader Jacking Locations
2015/06/18 Cat Reman Announces Availability of New Wheels With Installed Studs for Certain Machines {4201}
3412 Generator Set Engine Stalls Immediately After Starting
120 and 120 AWD Motor Grader Lifting and Tying Down the Machine
G3600 A4 Engines Engine Air Cleaner Service Indicator - Inspect
Machine Security System (MSS3i) Integrated System Schematic
3516C High Displacement Engine Sensor Signal (Analog, Passive) - Test
G3606 and G3608 Engines Engine Oil Pump - Install
3516C High Displacement Engine Component Location
Locating a Lost Autonomous Stop (A-Stop) Remote {79AU} Locating a Lost Autonomous Stop (A-Stop) Remote {79AU}
Machine Security System (MSS3i) Integrated Normal Operation
2015/06/26 A New Adapter Is Used with the Air Filter Indicator on Certain Commercial Engines {7452}
2015/06/25 A New Adapter Is Used with the Air Filter Indicator on Certain Machine Engines {1054, 7452}
Autonomy Log Processing Usage Instructions {7008, 7605} Autonomy Log Processing Usage Instructions {7008, 7605}
Procedure for Installing Operator Control System (OCS) On Workstation {7008, 7605} Procedure for Installing Operator Control System (OCS) On Workstation {7008, 7605}
3512C Generator Set Engine Engine Oil Filter Housing - Assemble
3512C Generator Set Engine Engine Oil Pan - Remove and Install
794 AC Off-Highway Truck Field Assembly Cooling Lines - Install