Piston and Rings
Show/hide table
| |
| Illustration 1 | g06167528 |
|
Typical example | |
Show/hide table
| Specification for 436-6352 Piston and Rod Gp , 436-6353 Piston and Rod Gp and 467-8328 Piston and Rod Gp | |||
|---|---|---|---|
| Item | Qty | Part | Specification Description |
| 1 | 1 | 314-2691 Piston Ring | Install the top piston ring with the side marked "UP" toward top of the piston. Orient the red color stripe face to the right of the piston ring end gaps. |
| Clearance between the ends of the top piston ring is |
|||
| Width of groove in new piston body assembly for piston ring is |
|||
| Thickness is |
|||
| 2 | 1 | 314-2692 Piston Ring | Install the intermediate piston ring with the side marked "UP" toward top of the piston. Orient the black color stripe face to the right of the piston ring end gaps. |
| Clearance between the ends of the intermediate piston ring is |
|||
| Width of groove in new piston body assembly for piston ring is |
|||
| Thickness is |
|||
| - | - | - | After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 ± 20 degrees apart from each other. |
| 3 | 1 | 314-2693 Oil Ring | The ends of the oil control piston ring should be at a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The white color stripe of oil ring spring should be visible at oil ring end gap. |
| Clearance between the ends of the new oil control piston ring is |
|||
| Width of groove in new piston body assembly for piston ring is |
|||
| Thickness is |
|||
| 4 | 1 | 7C-1412 Piston Pin | Thoroughly lubricate the piston pin with clean engine oil before the piston pin is inserted into the piston body assembly and the rod assembly. |
| Outside diameter is |
|||
| Length is |
|||
| Bore in the new piston body assembly for the piston pin is |
|||
| 5 | 2 | 7C-1413 Pin Retainer | Install the pin retainer with the word "OUT" is visible. After assembly, maintain a minimum clearance of |
Show/hide table
| |
| Illustration 2 | g06167529 |
|
Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| 6 | 1 | 314-2696 Bolt | Use the following procedure to tighten the bolt: 1. Lubricate the thread and supporting surface of bolt with Molykote Paste G-n Plus. 2. Tighten bolt to 3. Loosen the bolt. 4. Again, tighten bolt to 5. Again, tighten to an extra angle of 90 degrees. The bolt is reusable if, overall length of the bolt is less than |
Caterpillar Information System:
C280 Marine Engines Housing (Front)
C280 Marine Engines Cylinder Block
C280 Marine Engines Crankshaft Seals
C280 Marine Engines Connecting Rod
C280 Marine and Petroleum Engines Fuel Injection Lines
C280 Marine Engines Cylinder Liner
C280 Marine and Petroleum Engines Cylinder Block
C280 Marine Engines Camshaft
C280 Marine and Petroleum Engines Turbocharger
Generators for C15/C18 Engines Voltage Regulators
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Assemble
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Engine Oil Coolers - Disassemble
C280 Marine Engines Flywheel
Procedure for Installing Continuous Telematics Power Retrofit (CTPR) for Electric Power{7606} Procedure for Installing Continuous Telematics Power Retrofit (CTPR) for Electric Power{7606}
C9.3 Marine Engines Fuel Pressure Sensor
C3.4B Engines ECM - Replace
C3.4B Engines Electrical Connectors - Inspect
C280 Marine Engines Crankcase Pressure Sensor
C280 Marine Engines Atmospheric Pressure Sensor
G3516 Engines Thermocouple
C280 Marine Engines Turbocharger Inlet Pressure Sensor
3516C Marine Engines Auxiliary Sea Water Pump
464-6603 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000} 464-6603 Top End Overhaul Foundational Kit for 3516 Generator Set Engines{1000}
3516C Marine Engines Fumes Disposal Filter