Speed Control - Test
使用此步骤对油门位置传感器故障进行故障排除。 如果以下一个诊断代码为激活状态或易于重复,也使用本步骤。
Show/hide table
J1939 代码和描述 | CDL 代码和描述 | 注释 |
---|---|---|
91-3
油门踏板位置 1:电压高于正常值 |
91-3
油门位置传感器:电压高于正常值 |
电子控制模块(ECM)检测到不在可接受范围内的信号电压。
ECM 视油门位置为无效数据并采用默认值。 发动机转速将限制在高怠速上。 记录该代码。 |
91-4
油门踏板位置 1:电压低于正常值 |
91-4
油门位置传感器:电压低于正常值 |
ECM 检测到不在可接受范围内的信号电压。
ECM 视油门位置为无效数据并采用默认值。 发动机转速将限制在高怠速上。 记录该代码。 |
91-8
油门踏板位置 1:异常频率、脉冲宽度或周期 |
91-8
油门位置传感器:异常频率、脉冲宽度或周期 |
ECM 检测到不在可接受范围内的信号电压。
ECM 视油门位置为无效数据并采用默认值。 发动机转速将限制在高怠速上。 记录该代码。 |
注: 执行本程序中的步骤要求使用能够测量 PWM 工作循环和频率的万用表。
Show/hide table
所需工具 | ||
---|---|---|
零件号 | 零件名称 | 数量 |
7X-1710 | 万用表表笔 | 1 |
146-4080 | 数字万用表总成 | 1 |
326-4904 | 适配器缆线组件 | 1 |
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 检查传感器上的信号频率和工作循环 A. 把钥匙开关转到断开位置。 B. 从油门位置传感器接头线束侧的端子位置 C(油门位置)上拆下导线。 C. 将 326-4904 适配器电缆组件 (3 针抽头线束)安装到油门位置传感器的接头上。 D. 连接油门位置传感器接头。 E. 把钥匙开关转到接通位置。 F. 测量以下端子之间 326-4904 适配器电缆组件 (3 针抽头线束)上的频率和占空比: - B(数字回路)和 C(油门位置) G. 操作油门踏板的同时执行测量。 H. 把钥匙开关转到断开位置。 J. 拆下断开线束。 K. 将导线线束接头恢复为原来的配置。 |
频率 工作循环 |
结果:ECM 检测到油门信号频率或工作循环不正确。 频率低于 150 Hz 或高于 1000 Hz。 工作循环低于 5% 或高于 95%。 转至测试步骤 2。 结果:整个踏板范围内的频率和工作循环在技术规格范围内。 修理:修理或更换导线线束。 如果故障未得到排除,则转至测试步骤 2。 |
2. 检查传感器的电源电压 A. 把钥匙开关转到断开位置。 B. 断开油门位置传感器的导线线束接头。 C. 测量以下导线线束接头端子之间的电压: - A(8 V 电源)和 B(数字回路) |
7.5 VDC |
结果:传感器接头上的电源电压高于 7.5 VDC。 修理:导线正常。 更换传感器。 确认修理后故障得到排除。 结果:传感器接头上的电源电压不高于 7.5 VDC。 转速控制上没有电源电压。 修理:修理或更换导线线束。 确认修理后故障得到排除。 |
如果以上步骤未解决问题,请联系当地 Cat 代理商的技术通信员(TC)。 如需进一步的帮助,您的 TC 可以通过代理商解决方案网络(DSN)与您交谈。
Caterpillar Information System:
3512, 3508 and 3516 Generator Sets Maintenance Interval Schedule - Standby
Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159} Installation Procedure to Retrofit Overhead Guard and Front Window Guard Upgrade Kits on the Cab of Certain Large Excavators and Mobile Hydraulic Power Units {7159}
3512, 3508 and 3516 Generator Sets Maintenance Interval Schedule - Prime Power
Installation Procedure for the Jacket Water Bypass Tube Bracket on Certain 3512C Engines{1380} Installation Procedure for the Jacket Water Bypass Tube Bracket on Certain 3512C Engines{1380}
C280-16 Tier 4 Marine Engine and C280-12 Tier 4 Marine Engine Turbocharger - Remove and Install
C13 Industrial Engine Intake Manifold Air Pressure Is Low
C175-16 Locomotive Engine Turbocharger Turbine Temperature Is High
2014/11/21 A New Jacket Water Bypass Bracket Is Used on Certain 3512C Engines {1380}
C13 Industrial Engine Fuel Pressure Is Low
2014/10/27 New Guidelines for Valve Cover Base Threaded Insert on C27 and C32 Engines {1107, 1120}
2014/10/27 An Improved Installation Procedure for the Injector Top O-Ring Seal on C27 and C32 Machine Engines {1251, 1254, 1290, 1713}
PM3500 Power Modules Maintenance Interval Schedule - Prime Power
3512E Tier 4 Final Engines for Land Electric Drilling Coolant Level Is Low
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Signal (Analog, Passive) - Test
C280-08 Tier 4 Engine Fuel Priming Pump - Remove and Install
3512E Tier 4 Final Engines for Land Electric Drilling Sensor Signal (Analog, Active) - Test
C4.4 Engines General Information
Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153} Installation Procedure to Retrofit a 471-1985 Swivel Guard Upgrade Kit on Certain Excavators {7153}
3500 Generator Sets Maintenance Interval Schedule - Standby
2014/11/14 New EMCP 3.2/3.3 Software Is Now Available For Use On Certain Cat® Products {4490, 7620}
793F Off-Highway Truck Fuel Correction Factor - Set
3500 Generator Sets Maintenance Interval Schedule - Prime Power
3500 Generator Sets Maintenance Interval Schedule - High Displacement
C13 Industrial Engine Exhaust System Contains Oil