Rotor Bearing Oil Level - Check
Show/hide table
熱機油和高溫組件會導致人員受傷。 請勿讓熱油或發熱的組件接觸到皮膚。 |
Show/hide table
插圖 1 | g03707322 |
- 檢查液位前請讓機器保持水平,以確保取得正確的液位。
- 檢查轉子軸承油位。 機油必須顯示在光學液位指示器 (1) 上的半滿標記。
- 如果需要添加機油,請取下注油塞 (2) 並添加機油。 將油位維持在光學液位指示器 (1) 上的半滿標記。
- 清潔塞子 (2),然後將其裝回。
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil - Change
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Sample - Obtain
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Level - Check
XQC1200 and XQC1600 Power Modules Temperature Sensor (Exhaust) - Remove and Install
C8.7 Marine Engine Crankshaft Vibration Damper - Inspect
XQC1200 and XQC1600 Power Modules Inlet Manifold Temperature Sensor - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet Manifold Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
PM820, PM822, and PM825 Cold Planer Legs (Struts) - Lubricate
460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM620 and PM622 Cold Planer Hydraulic System Oil Sample - Obtain
PM620 and PM622 Cold Planer Hydraulic System Oil Level - Check
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Pressure Sensor - Remove and Install
460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM820, PM822, and PM825 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Service Door Pivot Pins - Lubricate
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Temperature Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Steering Cylinder Ends - Lubricate
PM820, PM822, and PM825 Cold Planer Track Drive - Inspect
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Level - Check
XQC1200 and XQC1600 Power Modules Engine Oil Pressure Sensor - Remove and Install - Filtered and Unfiltered
2014/08/01 A New Alternator and Mounting Hardware Are Used For Certain G3306B Engines {1405}
Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916} Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916}
2014/08/08 New Engine Software Is Used on Certain 3512C Well Fracturing Engines {1901, 1920}