Rotor Bearing Oil - Change
Show/hide table
 |
|
熱機油和高溫組件會導致人員受傷。 請勿讓熱油或發熱的組件接觸到皮膚。 |
Show/hide table
| 注意事項 |
|---|
|
在檢驗、保養、測試、調整及修理產品時，請小心確保油液有容器盛裝。 在打開任何艙室或拆卸任何含有用液的組件前，應準備好盛裝用液的適當容器。 請參閱特別出版品, N4NG2500, "代理商維修工具目錄"，以瞭解適合用來收集及容納 Cat® 產品之液體的工具和耗材。 按照當地的條例和法規棄置廢棄的油液。 |
Show/hide table
| |
| 插圖 1 | g03707322 |
- 檢查液位前請讓機器保持水平，以確保取得正確的液位。
- 取下注油塞 (1)。
- 取下排放塞 (2)，將機油排放到適當的容器中。 轉子軸承外殼的容量為
0.8 L (0.21 US gal) 。 - 清潔排放塞 (2)，然後裝回排放塞 (2)。
- 透過注油塞 (1) 的開口添加機油，直到油位位於光學液位指示器 (3) 上的半滿標記。
- 清潔注油塞 (1)，然後裝回注油塞 (1)。
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Sample - Obtain
PM820, PM822, and PM825 Cold Planer Pump Drive Oil Level - Check
XQC1200 and XQC1600 Power Modules Temperature Sensor (Exhaust) - Remove and Install
C8.7 Marine Engine Crankshaft Vibration Damper - Inspect
XQC1200 and XQC1600 Power Modules Inlet Manifold Temperature Sensor - Remove and Install
XQC1200 and XQC1600 Power Modules Inlet Manifold Pressure Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Moldboard Cutting Edge - Inspect/Adjust/Replace
PM820, PM822, and PM825 Cold Planer Legs (Struts) - Lubricate
460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9068 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM620 and PM622 Cold Planer Hydraulic System Oil Sample - Obtain
PM620 and PM622 Cold Planer Hydraulic System Oil Level - Check
PM820, PM822, and PM825 Cold Planer Hydraulic Foldable Canopy Cylinder Ends - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Bearing Oil Level - Check
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Pressure Sensor - Remove and Install
460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-9016 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
PM820, PM822, and PM825 Cold Planer Rotor Service Door Cylinder Pins - Lubricate
PM820, PM822, and PM825 Cold Planer Rotor Service Door Pivot Pins - Lubricate
XQC1200 and XQC1600 Power Modules Turbocharger Inlet Temperature Sensor - Remove and Install
PM820, PM822, and PM825 Cold Planer Steering Cylinder Ends - Lubricate
PM820, PM822, and PM825 Cold Planer Track Drive - Inspect
PM820, PM822, and PM825 Cold Planer Track Drive Planetary Oil Level - Check
XQC1200 and XQC1600 Power Modules Engine Oil Pressure Sensor - Remove and Install - Filtered and Unfiltered
2014/08/01 A New Alternator and Mounting Hardware Are Used For Certain G3306B Engines {1405}
Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916} Improper Installation of the 274-6717 Crankcase Pressure Sensor on 3500 Commercial Engines{1408, 1439, 1916}