C15-XQ400 Rental Generator Set Caterpillar


Maintenance Interval Schedule - Standby

Usage:

C15 X4R
Ensure that all safety information, warnings, and instructions are read and understood before any operation or any maintenance procedures are performed.

An authorized operator may perform the maintenance items with daily intervals. An authorized operator may perform the maintenance items with intervals of every week. The maintenance that is recommended for all other maintenance intervals must be performed by an authorized service technician or by your Cat dealer.

The user is responsible for the performance of all maintenance which includes the following items: performing all adjustments, using proper lubricants, fluids, and filters and replacing old components with new components due to normal wear and aging .

Failure to adhere to proper maintenance intervals and procedures may result in diminished performance of the product and/or accelerated wear of components.

Before each consecutive interval is performed, all maintenance from the previous intervals must be performed.

Choose the interval that occurs first in order to determine the correct maintenance interval: fuel consumption, service hours and calendar time . Products that operate in severe operating conditions may require more frequent maintenance.

All of the following will affect the oil change interval: operating conditions, fuel type, oil type and size of the oil sump . Scheduled oil sampling analyzes used oil in order to determine if the oil change interval is suitable for your specific engine.

Refer to this Operation and Maintenance Manual, "Engine Oil and Filter - Change" in order to determine the oil change interval that is suitable for your specific engine.

To determine the maintenance intervals for the overhauls, refer to this Operation and Maintenance Manual, "Maintenance Recommendations" .

Unless other instructions are provided, perform maintenance and perform repairs under the following conditions:

The starting system is disabled.

The engine is stopped.

The generator does not pose an electrical shock hazard.

The generator is disconnected from the load.

When Required

Aftercooler Core - Clean/Test
Battery - Replace
Battery or Battery Cable - Disconnect
Circuit Breakers - Reset
Enclosure - Inspect
Fuel System - Prime
Fuel System Water Separator - Drain
Trailer - Inspect

Every Week

Battery Charger - Check
Battery Electrolyte Level - Check
Cooling System Coolant Level - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel Tank Water and Sediment - Drain
Walk-Around Inspection

Every 6 Months

Cooling System Coolant Sample (Level 1) - Obtain

Every Year

Alternator - Inspect
Belts - Inspect/Adjust/Replace
Cooling System Coolant Sample (Level 2) - Obtain
Crankshaft Vibration Damper - Inspect
Engine - Clean
Engine Air Cleaner Element (Dual Element) - Clean/Replace
Engine Crankcase Breather - Clean
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Engine Speed/Timing Sensors - Check/Clean/Calibrate
Engine Valve Lash - Inspect/Adjust
Fan Drive Bearing - Lubricate
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Hoses and Clamps - Inspect/Replace
Radiator - Clean
Starting Motor - Inspect
Water Pump - Inspect

Every 3 Years

Cooling System Coolant Extender (ELC) - Add
Cooling System Water Temperature Regulator - Replace
Turbocharger - Inspect

Every 6 Years

Cooling System Coolant (ELC) - Change

Caterpillar Information System:

C15-XQ400 Rental Generator Set Maintenance Interval Schedule - Prime
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057} Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
C4.4 Generator Set Engine Troubleshooting
336F XE Excavator Service Interval Chart
C3.3B and C3.8 Engines for Caterpillar Built Machines Motorized Valve - Test
323F SA and 323F LN Excavator Radiator, Aftercooler and Oil Cooler Cores - Clean
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Exhaust Temperature Is Low
XQ570 Rental Generator Set Refill Capacities and Recommendations
Well Service Pumps Pump (Fluid End) Plungers and Packing - Inspect
C15-XQ400 Rental Generator Set Refill Capacities and Recommendations
C9-XQ300 Rental Generator Set Refill Capacities and Recommendations
2014/07/25 New Software Is Available for Certain C27 and C32 Industrial Engines {1901, 1920}
2014/07/07 A New Coupling Hub Has Been Released for 3524 Engines {3279}
C3.4B Industrial Engine Before Starting Engine
Caterpillar Machine Fluids Recommendations Expanded Mining Fluids
Improved Camshafts and Rocker Arm Assemblies Are Now Available For Hydraulic Mining Shovels and Rotary Drills Equipped with C27 and C32 Engines {1123, 1210} Improved Camshafts and Rocker Arm Assemblies Are Now Available For Hydraulic Mining Shovels and Rotary Drills Equipped with C27 and C32 Engines {1123, 1210}
3512C Marine Auxiliary Generator Set Engines with Dynamic Gas Blending Detonation Occurrence
3512, 3508 and 3516 Generator Sets Product Description
3512C Marine Auxiliary Generator Set Engines with Dynamic Gas Blending Exhaust Temperature Is Low
2014/08/27 A New Improved Removal and Installation of the Injector Harness Procedure is Now Used on Certain C13, C15 and C18 Engines {1251, 1408}
C3.3B and C3.8 Engines for Caterpillar Built Machines Electrical Connectors - Inspect
C13-XQ350 Rental Generator Set Maintenance Interval Schedule - Prime
C13-XQ350 Rental Generator Set Maintenance Interval Schedule - Standby
2014/07/11 A New Kit Part Number Is Used on Certain G3508 Engines {1000, 1052, 1270, 191N}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.