Balancer - Remove
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 9U-6198 | 曲轴转动工具 | 1 |
B | 230-6283 | 正时销(曲轴) | 1 |
C | 231-8849 | 正时销(平衡器) | 1 |
D | 1P-2320 | 组合式拉拔器 | 1 |
开始:
- 拆下发动机油底壳。 请参阅拆解和组装, "发动机油底壳 - 拆卸和安装"。
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"。
注: 要拆卸平衡器,必须从机器上卸下发动机。 应将发动机倒置安放在适当的台架上。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 使用工具 (A) 转动曲轴,使 1 号活塞处于上止点位置。
Show/hide table
图 1 g01259627 典型示例 - 将工具 (B) 穿过孔 (X) 安装到前齿轮室中。 使用工具 (B),将曲轴锁定到位。
Show/hide table
图 2 g01259635 典型示例 - 卸下螺栓 (3) 和吸油管 (2)。
- 从吸油管上卸下密封垫。
Show/hide table
图 3 g01252310 典型示例 - 将工具 (C) 安装到平衡器 (1) 上。 确保已将工具 (C) 在驱动轴 (5) 的孔中啮合。
- 将适当的起吊设备连接在平衡器 (1) 上。 支撑住平衡器的重量。 平衡器重量约为
23 kg (51 lb) 。 - 拆下螺栓 (4)。 使用起吊设备卸下平衡器。
Show/hide table
图 4 g01259636 - 除非定位销损坏,否则不要从曲轴上卸下定位销 (6) 和定位销 (7)。
注: 平衡器装置是一个不可维修的部件。 发动机机油泵和发动机机油安全阀是平衡器中唯一可以维修的零件。
- 拆下发动机机油安全阀。 请参阅拆解和组装, "发动机机油安全阀 - 拆卸和安装"。
Show/hide table
图 5 g01478152 典型示例 - 拆下螺栓 (8) 和轮毂 (9)。 卸下惰齿轮 (10) 和止推垫圈 (11)。
Show/hide table
图 6 g01259631 典型示例 - 拆下螺母 (12)。 使用工具 (D),从机油泵的轴上卸下齿轮 (13)。
注: 不要通过使用正时销锁定平衡器的方式来松开螺母 (12)。
- 卸下螺栓 (14),然后卸下前齿轮室 (15)。
- 卸下外转子 (17),然后卸下内转子 (16)。
注: 标出转子的旋向。
Caterpillar Information System:
793F and 797F Off-Highway Trucks Braking System E653 Low Secondary Brake Accumulator Pressure
C3.4B Engines for Caterpillar Built Machines Cylinder Head
C4.4 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C4.4 Engines for Caterpillar Built Machines Turbocharger - Install - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C4.4 Engines for Caterpillar Built Machines Balancer - Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C3.4B Engines for Caterpillar Built Machines Camshaft Bearings
C8.7 Marine Engine Engine Oil Level Gauge - Calibrate
C3.4B Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
C4.4 Engines for Caterpillar Built Machines Electronic Control Module - Remove and Install
C3.4B Engines for Caterpillar Built Machines Main Bearing Journal
C3.4B Engines for Caterpillar Built Machines Connecting Rod