Turbocharger - Install - Top Mounted Turbocharger
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 4C-4030 | 螺纹锁固胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保涡轮增压器清洁且无损坏。 检查涡轮增压器有无磨损。 更多信息请参阅系统操作、测试和调整, "涡轮增压器检查"。 如果涡轮增压器磨损,必须更换整个涡轮增压器。
- 测试废气旁通阀执行器 (20) 是否正常工作。 请参阅系统操作、测试和调整, "涡轮增压器检查"。 如果废气旁通阀执行器损坏或不在规定限制范围内工作,必须更换整个涡轮增压器。
Show/hide table
图 2 g01782773 - 清洁排气歧管 (1) 的密封垫表面。 如有必要,将螺柱 (18) 安装到排气歧管上。 拧紧螺柱至扭矩为
18 N·m (13 lb ft) 。注: 涡轮增压器安装期间应支撑排气歧管。
- 将新密封垫 (16) 安装到排气歧管 (1) 上。
- 将涡轮增压器 (13) 定位到排气歧管 (1) 上。
- 安装螺母 (14)。 拧紧螺母至扭矩为
44 N·m (32 lb ft) 。 - 确保管组件 (6) 清洁且无损坏。 更换任何损坏的部件。
- 将新密封垫 (15) 和螺栓 (17) 安装到管组件 (6) 上。
- 将管组件 (6) 安装到涡轮增压器 (13) 上。 用手拧紧螺栓 (17)。
- 将排气歧管 (1) 和涡轮增压器组件安装到缸盖上。 请参阅拆解和组装, "排气歧管 - 拆卸和安装"以了解正确程序。
- 从进油口 (19) 处拆下螺塞。 参考图 1。 用清洁的发动机机油通过进油口润滑涡轮增压器轴承。 将压缩机叶轮转动几次以便润滑轴承。
- 确保管组件 (2) 清洁且无损坏。 更换任何损坏的部件。
- 将中空螺栓 (11) 和新的密封垫圈 (12) 安装到管组件 (2) 上。
Show/hide table
图 3 g01780893 - 将中空螺栓 (7) 和新的密封垫圈 (9) 安装到管组件 (2) 上。
- 将管组件 (2) 安装到涡轮增压器 (13) 上。 用手拧紧中空螺栓 (11)。 参考图 2。
- 用手将中空螺栓 (7) 安装到缸体中。
- 将一个新密封垫 (8) 定位到管组件 (6) 的法兰和缸体之间。 安装螺栓 (10) 并用手拧紧。
- 拧紧中空螺栓 (7) 至扭矩为
20 N·m (14 lb ft) 。 拧紧螺栓 (10) 至扭矩为22 N·m (16 lb ft) 。 - 拧紧中空螺栓 (11) 至扭矩为
20 N·m (14 lb ft) 。 拧紧螺栓 (17) 至扭矩为9 N·m (80 lb in) 。 参考图 2。 - 将管夹的螺栓 (3) 安装到缸体中。 将螺栓 (3) 拧紧至扭矩为
44 N·m (32 lb ft) 。 - 将管夹的螺栓 (5) 和隔套 (4) 安装到缸体中。 拧紧螺栓 (5) 至扭矩为
44 N·m (32 lb ft) 。 - 如果涡轮增压器有排气弯管,应安装排气弯管。 请参阅拆解和组装, "排气弯管 - 拆卸和安装"。
- 连接排气管。
- 将出气软管连接到涡轮增压器 (13) 上。
如果发动机配备一个空气管,安装该空气管,然后将密封垫安装到缸盖上。 将工具 (A) 涂敷在空气管紧固件上。 拧紧紧固件至扭矩为
22 N·m (16 lb ft) 。拧紧软管卡箍至扭矩为
5 N·m (44 lb in) 。注: 如果出气软管有一个反射式隔热罩,确保该隔热罩安装后朝向发动机。
- 将进气软管连接到涡轮增压器 (13) 上。
Show/hide table
图 1 | g01784893 |
典型示例 |
Caterpillar Information System:
C4.4 Engines for Caterpillar Built Machines Turbocharger - Remove - Top Mounted Turbocharger
C4.4 Engines for Caterpillar Built Machines Lifter Group - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
C4.4 Engines for Caterpillar Built Machines Fuel Pressure Sensor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C175-16 PETROLEUM ENGINES Fuel Transfer Pump - Remove and Install
XQC1200 and XQC1600 Power Modules Exhaust Manifold - Remove and Install
C280 Marine Engines Crankcase Pressure Is High
C175-16 PETROLEUM ENGINES Fuel Priming Pump - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Elbow - Remove and Install
C3.4B Engines for Caterpillar Built Machines Cylinder Head
793F and 797F Off-Highway Trucks Braking System E653 Low Secondary Brake Accumulator Pressure
C4.4 Engines for Caterpillar Built Machines Balancer - Remove
C4.4 Engines for Caterpillar Built Machines Balancer - Install
C3.4B Engines for Caterpillar Built Machines Rocker Shaft
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines Without a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Engine Oil Relief Valve - Remove and Install - Engines with a Balancer Unit
C4.4 Engines for Caterpillar Built Machines Refrigerant Compressor - Remove and Install
C4.4 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C3.4B Engines for Caterpillar Built Machines Camshaft Bearings
C8.7 Marine Engine Engine Oil Level Gauge - Calibrate