Track Carrier Roller
Show/hide table
| |
| Illustration 1 | g03450039 |
|
Typical example | |
Show/hide table
| Item | Qty | Part Number | Specification Description |
|---|---|---|---|
| 1 | 1 | 4H-9105 O-Ring Seal | Lubricate the bore lightly with the lubricant that is being sealed. |
| 2 | 1 | 475-8471 Duo-Cone Seal Gp | Rubber toric rings and all surfaces contacting the toric seals must be clean and dry at assemblies. Before assembly, apply a thin film of oil to the contacting surfaces of the metal ring seals. Assemble the ring seals square with the bore and the toric ring must not be bulged or twisted. |
| 3 | 1 | 6Y-8172 Carrier Roller Bearing | Bore after assembly is |
| 4 | 3 | 8T-0273 Bolt | Torque to |
| 5 | 1 | - | Before assembly, the length of the shaft (A) must be free of paint.
The length of the shaft (A) is The length of the shaft (A) is |
| 6 | - | 8T-0273 Bolt | Torque to |
| - | - | - | End play for the track roller shaft:
Minimum end play is Maximum end play is End play for the track roller shaft for 8E-4623: Minimum end play is Maximum end play is |
Show/hide table
| (1) | Not applicable for 8E-4623 |
| (2) | For 300-4610 and 8E-4623 |
| (3) | For 300-4611 and 542-8380 |
Caterpillar Information System:
G3306B Gas Engines Alternator Mounting
188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703} 188-3922 Broken Exhaust Bolt and Stud Removal Group for 3114, 3116, 3126, 3126B, 3176, 3176B, C-10, and C12 Engines{0374, 0599, 0701, 0702, 0703}
CX31 and CX31 HT On-Highway Transmissions Transmission Operation
CX31 and CX31 HT On-Highway Transmissions Transmission Control
Using the 9U-5792, 4C-5052, 4C-5054, 4C-3670, and 4C-3680 Hydraulic Hose Machines{0374, 0599, 0684, 0738, 5057} Using the 9U-5792, 4C-5052, 4C-5054, 4C-3670, and 4C-3680 Hydraulic Hose Machines{0374, 0599, 0684, 0738, 5057}
C15 and C18 Engines for Caterpillar Built Machines General Information
Three60 Precision Control System System Overview
CX31-P600 Petroleum Transmission Power Train Hydraulic System
2013/10/02 Improved Gear Train Components are Now Used on TH48-E80 Petroleum Transmissions {3064, 3160}
Procedures for Using the 212-1503 Portable Parts Washer{0374, 0599, 0680, 0699, 0700} Procedures for Using the 212-1503 Portable Parts Washer{0374, 0599, 0680, 0699, 0700}
CX31 and CX31 HT On-Highway Transmissions Magnetic Screen (Transmission) - Clean
CX31 and CX31 HT On-Highway Transmissions Breather (Transmission) - Clean
CX31 and CX31 HT On-Highway Transmissions Capacities (Refill)
795F AC and 795F AC XQ Off-Highway Trucks Hood Tilt Assist Spring - Lubricate
C15 and C18 Engines for Caterpillar Built Machines ECM - Replace
CX31 and CX31 HT On-Highway Transmissions Reference Material
C13 and C15 Generator Sets Battery Disconnect Switch - If Equipped
2013/11/04 New Boost Pressure Sensor Location Is Used for Certain 3512 Petroleum Engines {1408, 1439, 1917}
C13 and C15 Generator Sets Generator Start-up Checklist
C15 and C18 Engines for Caterpillar Built Machines Programmable Parameters
G3600 A4 Engines Coolant (NGEC) - Change
G3600 A4 Engines Coolant Level - Check
2013/09/25 An Improved Fuel Transfer Pump Assembly Is Now Available for Certain C9.3 ACERT Engines {1251, 1256, 1290}
G3600 A4 Engines Coolant Level Switch - Inspect/Test