Installation of the 384-9286 Protection Cover Gp for Certain Clean Emissions Module Arrangements{108D, 795C}
- Engine:
- C13 (S/N: KWJ1-UP)
- C15 (S/N: LDN1-UP)
- C18 (S/N: BDN1-UP)
- C15 (S/N: LDN1-UP)
- Industrial Engine:
- C9.3 (S/N: C9N1-UP; D9N1-UP)
Introduction
Do not perform any procedure that is outlined in this publication until you read and understand the information that is contained in this document.
Required Parts
The new 384-9286 Protection Cover Gp is available for certain 13 inch clean emissions module arrangements. Table 1 contains the part numbers that are included for installation of the cover group. Table 2 contains the part numbers that need removed before installation.
Show/hide table
| Item | Qty | Part Number and Description |
|---|---|---|
| 1 | 1 | 384-9287 Cover Gp |
| 2 | 1 | 384-9288 Bracket As |
| 3 | 1 | 384-9289 Bracket As |
| 4 | 1 | 384-9290 Bracket As |
| 5 | 1 | 384-9291 Bracket As |
| 6 | 1 | 384-9292 Bracket As |
| 7 | 5 | 7X-0818 Bolt |
| 8 | 2 | 7X-2533 Bolt |
| 9 | 5 | 7X-7729 Washer |
| 10 | 2 | 8T-4138 Bolt |
| 11 | 4 | 8T-4224 Hard Washer |
| 12 | 4 | 8T-4908 Bolt |
| 13 | 2 | 8T-4971 Bolt |
| 14 | 6 | 9X-8256 Washer |
Show/hide table
| Item | Qty | Part Number and Description |
|---|---|---|
| 15 | 2 | 186-0815 Bolt |
| 16 | 2 | 344-1200 Hard Washer |
| 17 | 1 | 363-3265 Bracket As |
| 18 | 2 | 311-8366 Hard Washer |
| 19 | 2 | 344-1193 Bolt |
| 20 | 2 | 204-0813 Bolt |
| 21 | 3 | 344-1200 Hard Washer |
| 22 | 2 | 344-1207 Bolt |
| 23 | 2 | 198-4764 Hard Washer |
Removal of Hardware for Models EE018, EE019, EE020, and EE021
- Remove the two bolts (15), washers (16), and bracket assembly (17) from the 365-9473 Mounting Plate .
Show/hide table
 | |
| Illustration 1 | g03406606 |
- Remove the two bolts (18) and two washers (19) from the bracket assembly holding the harness connection.
Show/hide table
 | |
| Illustration 2 | g03406642 |
- Remove the two bolts (20) and two washers (21) from the 343-3877 Plate As .
Show/hide table
 | |
| Illustration 3 | g03406647 |
- Remove the two bolts (22), two hard washers (23), and two washers (21) from between the mounting plate and bracket. Retain clip (A) for reinstallation in Step 2.
Show/hide table
 | |
| Illustration 4 | g03407158 |
(A) 341-3624 Clip | |
Installation Steps for the 384-9286 Protection Cover Gp
- Install bracket assembly (2) using two bolts (10) and two washers (14). Torque the bolts to 12 ± 3 N·m (106 ± 27 lb in).
Show/hide table
 | |
| Illustration 5 | g03406665 |
- Install bracket assembly (3) using two bolts (13) and two washers (14) in between the 363-3554 Bracket and the 365-9473 Mounting Plate . Reinstall clip (A) that was removed in Step 4. Torque the bolts to 12 ± 3 N·m (106 ± 27 lb in).
Show/hide table
 | |
| Illustration 6 | g03406677 |
- Install bracket assembly (4) using two bolts (12) and two washers (11). Torque the bolts to 28 ± 7 N·m (250 ± 62 lb in).
Show/hide table
 | |
| Illustration 7 | g03406697 |
- Install bracket assembly (5) using two bolts (8) and two washers (14). Torque the bolts to 12 ± 3 N·m (106 ± 27 lb in).
Show/hide table
 | |
| Illustration 8 | g03406740 |
- Install bracket assembly (6) using two bolts (12) and two washers (11) behind the mounting plate. Torque the bolts to 28 ± 7 N·m (250 ± 62 lb in).
Show/hide table
 | |
| Illustration 9 | g03406763 |
- Install cover group (1) using five bolts (7) and five washers (9). Torque the bolts to 28 ± 7 N·m (250 ± 62 lb in).
Show/hide table
 | |
| Illustration 10 | g03406772 |
Caterpillar Information System:
3512E Engines for Well Stimulation Pumps Cover Group (Front Housing)
3516C Petroleum Engines Flywheel
C15 Petroleum Generator Set Engines Belt Tightener
3516C Petroleum Engines Flywheel Housing Cover
C7.1 Industrial Engine Diesel Exhaust Fluid Tank - Flush
C7.1 Industrial Engine Fuel and the Effect from Cold Weather
C7.1 Industrial Engine Aftertreatment SCR System Dosing - Test
3516C Marine Engines Thermostatic Valve
C3.4B Engines for Caterpillar Built Machines Diesel Exhaust Fluid Quality - Test
3516C Petroleum Engines Water Lines
3500B Marine Propulsion Engines Maintenance Interval Schedule
New Connecting Rod Bolts Are Available for C175 Engines{1218, 7553} New Connecting Rod Bolts Are Available for C175 Engines{1218, 7553}
3516C Petroleum Engines Engine Speed/Timing Sensor - Remove and Install
435-8503 Major Engine Overhaul Foundational Kit for 3406E Marine Engines{1000} 435-8503 Major Engine Overhaul Foundational Kit for 3406E Marine Engines{1000}
3512C Oil Well Service Engines Declaration of Conformity
3512E HD Petroleum Engine Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace - If Equipped
3516C Petroleum Engines Engine Oil Pressure Sensor - Remove and Install
C7.1 Industrial Engine Solenoid Valve (DEF Heater Coolant) - Remove and Install
C7.1 Industrial Engine Manifold (DEF Heater) - Remove and Install
2013/10/17 A New Expansion Tank Assembly Is Used on Certain 3500 Marine Engines {1354}
2014/01/17 Special Instructions Are Available for Retrofitting the Dynamic Gas Blending Kits on Certain 3512B Engines {1250, 1280}
3512C Petroleum Engines Electronic Control Module (Engine) - Remove and Install
C13 Industrial Engine Injector (Diesel Exhaust Fluid) - Replace
C15 and C18 Engines for Caterpillar Built Machines Fuel Filter and Water Separator