Electronic Unit Injector - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 5F-4764 | 撬杆 | 1 |
B | 8T-2998 | 润滑剂 | - |
C | 1U-5718 | 真空泵 | 1 |
169-7372 | 油液取样瓶 | - | |
4C-4057 | 管
|
- | |
D | 4C-5552 | 大号孔刷 | 1 |
E | 8T-7765 | 表面调节垫 | - |
开始:
- 拆下摇臂和摇臂轴。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下气门桥 (1)。 记下气门桥的位置和方位,以便于安装。
- 断开线束组件 (2)。
Show/hide table
图 2 g01259759 Show/hide table注意 在拆卸过程中,如果喷油器固定螺栓松动,应及时检查喷油器孔的磨损和破损情况。 换掉垫圈和隔套。
- 将螺栓 (3) 和隔套 (4) 从卡箍 (5) 上拆下。
- 为便于安装,在电子单体喷油器 (6) 上作出识别标记。 必须把每个电子控制单体喷油器安装回缸盖中的原来位置。
Show/hide table
图 3 g01259777 - 在螺栓孔内利用工具 (A) 将卡箍 (5) 和电子单体喷油器 (6) 从缸盖上撬下。
注: 工具 (A) 使用不当可损坏弹簧或单体喷油器。
- 将电子单体喷油器 (6) 从缸盖上拆下。
Show/hide table
图 4 g01259809 - 将 O 形密封圈 (7) 从电子单体喷油器 (6) 上拆下。
Show/hide table
图 1 | g01259747 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 利用工具 (C) 将燃油和机油从气缸中排出。 安装电子单体喷油泵之前,尽可能完全排出缸体中的燃油和机油。 可能需要多排几次。
- 利用工具 (D) 清除电子单体喷油器套筒内的积碳。
- 再用工具 (E) 清除位于电子单体喷油泵套筒内部底座区域的积碳。
Show/hide table
图 5 g01259809 - 将 O 形密封圈 (7) 安装到电子单体喷油器 (6) 上。 使用按 50/50 比例混合的清洁发动机机油和工具 (B) 润滑一下顶部两个 O 形密封圈。
Show/hide table
图 6 g01259759 Show/hide table注意 当换掉电子控制单体喷油器的时候,新喷油器的代码必须得通过电气伺服工具上的校准菜单编入发动机个人模块软件中。 如果没有输入新喷油器的代码,将会默认应用原来喷油器的特性设置。
如果不可能立刻将喷油器代码编入个人模块软件,对发动机也不会产生很大的伤害。 不过应该尽快编入电子控制单体喷油器的代码,以便能发挥发动机的最大性能。
- 将电子单体喷油器 (6) 和卡箍 (5) 装入缸盖内的原始位置。
- 安装隔套 (4) 和螺栓 (3)。 拧紧螺栓 (3) 至扭矩为
55 ± 10 N·m (41 ± 7 lb ft) 。Show/hide table图 7 g01259747 - 连接线束组件 (2)。
- 安装气门桥 (1)。
注: 确保气门桥的凹槽端指向摇臂轴。
- 排出燃油系统中的空气。 请参阅测试和调整, "燃油系统 - 注油"。
结束:
- 安装摇臂和摇臂轴。
Caterpillar Information System:
WS223, WS223 SS, WS223 XD, WS255, WS255 SS, WS255 XD, WSP223, WSP255, WSF223, WSF223 SS, WSF223 XD, WSF255, WSF255 SS and WSF255 XD Well Stimulation Pumps Flange (Discharge) - Remove and Install
2013/06/18 A New Jumper Harness Is Now Installed on Certain C32 Marine Engine Harnesses {1408}
C7.1 Marine Generator Set Reference Material
C15 and C18 Engines for Caterpillar Built Machines Valve Mechanism Cover Base - Remove and Install
2013/06/13 New Injection Assemblies Are Equipped with Flow Indicators for Certain Retrofit Selective Catalytic Reduction Systems {108I}
C175-16 Locomotive Engine Engine Oil Temperature Sensor
C32 Generator Set Voltage Regulators - R450T Automatic Voltage Regulator (AVR)
C7.1 Industrial Engine Product Storage
C13, C15, and C18 Tier 4 Final Engines Coolant Level Sensor
C175-16 and C175-20 Engines for Off-Highway Trucks Connecting Rod Bearings
C7.1 Marine Generator Set Coolant Sample (Level 1) - Obtain
New Water Pump Seal and Water Pumps Are Used on Certain 3500 and G3500 Engines {1361} New Water Pump Seal and Water Pumps Are Used on Certain 3500 and G3500 Engines {1361}
C15 and C18 Engines for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Disassemble
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Module - Assemble
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Filter - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Diesel Exhaust Fluid Pump - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Electronic Control (Diesel Exhaust Fluid) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Manifold (DEF Heater) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Voltage Control (Load Protection) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Solenoid Valve (DEF Heater Coolant) - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C32 Generator Set Fuel Related Components in Cold Weather
C15 and C18 Engines for Caterpillar Built Machines Catalyst (SCR) - Remove and Install