Diesel Particulate Filter - Install - Through Flow Diesel Particulate Filter
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 波纹管保护器     | 1     |
Show/hide table
在处理用过的柴油微粒滤清器或催化转化器消声器时,请配戴护目镜、手套、防护服以及经过职业安全与健康管理局(NIOSH)批准的 P95 或 N95 半面式防尘面罩。 否则可能造成人身伤害。 |
Show/hide table
注意 |
---|
不要敲打柴油颗粒滤清器(DPF)组件的任何部位。 不要让任何物体接触 DPF 的内芯。 如果 DPF 的内芯损坏,必须更换组件。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 如果将柔性排气管作为一个整体拆下,请参阅拆解和装配, "柔性排气管 - 拆卸和安装",了解正确的安装步骤。
- 如有必要,将温度传感器 (3) 和 (9) 安装到 DPF 中。 有关正确步骤,请参阅拆解和装配, "温度传感器 (DPF) - 拆卸和安装"。
Show/hide table
图 1 | g03017439 |
Show/hide table
图 2 | g03017436 |
Show/hide table
图 3 | g03022697 |
- 将新的 V 形带箍定位到柔性排气管 (8) 上。
- 将适当的起吊设备连接到柴油颗粒滤清器(DPF)组件 (6) 上。 DPF 的重量约为 15 kg (33 lb)。
- 使用适当的起吊设备将 DPF 安装到安装支架 (12) 上。 确保柔性排气管正确座合在涡轮增压器和 DPF 上,且定位销 (13) (未显示)完全接合。
注: 确保排气按临时标记的方向流动。
- 将适当的起吊设备从 DPF 组件上拆下。
- 将卡箍 (11) 定位到 DPF (6) 上。 宽松地安装螺栓 (10) 。
- 将原始设备制造商(OEM)排气管组件松松安装到 DPF 的出口段 (4) 。
- 将 DPF (6) 和卡箍 (11) 上的临时对准标记对准在位置 (A), (B), (C) 和 (D) 。
注: 确保柔性排气管波纹管不受任何过度应力。
- 如果正在安装新的 DPF,必须使用柔性排气管 (8) 作为参照点来对准 DPF。
注: 确保柔性排气管波纹管不受任何过度应力。
- 将 V 形带箍定位到 DPF 上。 拧紧柔性排气管卡箍。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装"。
- 将 OEM 排气管组件拧紧到 DPF 的出口段。 有关正确的步骤,请参阅 OEM 信息。
- 确保 DPF 安装在原位,并且所有临时对准标记已对准。
注: 确保柔性排气管波纹管不受任何过度应力。
- 分三个阶段均匀拧紧螺栓 (10) 。
将螺栓 (10) 拧紧至初始扭矩为 8 N·m (71 lb in)
将螺栓 (10) 拧紧至第二扭矩为 16 N·m (141.6 lb in)
将螺栓 (10) 拧紧至最终扭矩为 25 N·m (221 lb in)。
- 如有必要,将工具 (A) 从柔性排气管 (8) 上拆下。
- 将导线线束组件连接到温度传感器 (9) 上的接头 (1) 。
- 将导线线束组件连接到温度传感器 (3) 上的接头 (2) 。
- 将压力传感器管组件 (5) 连接到 DPF。 拧紧接头至扭矩为 25 N·m (221 lb in)。
- 将压力传感器管组件 (7) 连接到 DPF。 拧紧接头至扭矩为 30 N·m (265 lb in)。
End By:
- 如果 DPF 需要进行烟灰保养,将需要使用电子维修工具来执行 "DPF 烟灰清洁"步骤。
- 如果需要更换 DPF,并且已安装新的 DPF,将需要使用电子维修工具来执行 "DPF 更换复位"步骤。
Caterpillar Information System:
Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101} Caterpillar Off-Highway Truck (777, 785, 789, 793, and 797) Torque Converter Removal and Installation Technician Checklist {0372, 0374, 3101, 3101}
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove - Wall Flow Diesel Particulate Filter
2013/06/13 Improved 3412 Marine Bundled Repair Solution Foundational Kits Are Available {1000}
C32 Generator Set Sound Information
Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D} Customer Assembly Requirements for C7.1, C4.4, and C3.4B Engines {1000, 108D}
C32 Generator Set Plate Locations and Film Locations
Water Delivery System and 777F WTR, 777G WTR and 785D WTR OEM Off-Highway Trucks Service Tools
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Water Pump (Stainless Steel) - Remove and Install
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Water Pump (Stainless Steel) - Disassemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Water Pump (Stainless Steel) - Assemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Water Cannon - Disassemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Water Cannon - Assemble
C32 Generator Set Reference Material
C3.4B Engines for Caterpillar Built Machines Diesel Particulate Filter - Install - Wall Flow Diesel Particulate Filter
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Springs - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
C3.4B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
374F Excavator Machine Systems Relief Valve (Pilot) - Test and Adjust
C13 Engine for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
326F and 330F Excavator Machine Systems Boom Drift Reduction Valve
CG137-08 and CG137-12 Industrial Engines General Information
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Performance - Test
CG137-08 and CG137-12 Industrial Engines Catalytic Converter Substrate - Inspect
C175-16 Locomotive Engine Exhaust Manifold