Control Manifold (Front) - Disassemble
Disassembly Procedure
Start By:
- Remove the control manifold.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Put identification marks on components to aid in assembly.
Note: Cleanliness is an important factor. Before the disassembly procedure is started, clean the exterior of the components to prevent dirt from entering the internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly procedures on a clean work surface. Keep components covered and protected at all times.
- Remove three cartridge nuts (1). Remove five solenoids (2) from the valve cartridges.
Show/hide table
Illustration 1 | g03387931 |
- Remove three valve cartridges (4) from control manifold (3) .
Note: Three O-rings (5) are located on each valve cartridge (4) .
Show/hide table
Illustration 2 | g03387932 |
Show/hide table
Illustration 3 | g03387934 |
- Remove four fittings (6) .
Note: An O-ring (7) is located on each fitting (6) .
Show/hide table
Illustration 4 | g03387937 |
Show/hide table
Illustration 5 | g03387939 |
Caterpillar Information System:
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Control Manifold Group (Front) - Remove and Install
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Control Valve (Water) - Disassemble
C280-16 Engine Engine Oil Coolers - Disassemble
C32 Generator Set General Hazard Information
374F Excavator Hydraulic System Electronic Control (Swing System)
C280-16 Generator Set Engine for Nuclear Applications Aftercooler Coolant Temperature Is High
C13, C15, and C18 Tier 4 Final Engines Injector (Diesel Exhaust Fluid)
C13, C15, and C18 Tier 4 Final Engines Diesel Particulate Filter
C13, C15, and C18 Tier 4 Final Engines Exhaust Combustion (ARD) and Mounting
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines
C13, C15, and C18 Tier 4 Final Engines Mounting Frame
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Control Manifold (Rear) - Disassemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Control Manifold Group (Rear) - Remove and Install
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Control Valve (Water) - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Radiator
CAT Water Delivery System (WDS) and 777G WTR OEM Off-Highway Truck/Tractor Cooling Group - Remove and Install
Support Tool for the Three60 Precision Controller{7610} Support Tool for the Three60 Precision Controller{7610}
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Display Module - Remove and Install
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Electronic Control Module - Remove and Install
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Gear Pump (Charge) - Assemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Gear Pump (Charge) - Disassemble
CAT Water Delivery System (WDS) and 785D WTR OEM Off-Highway Truck/Tractor Hydraulic Oil Cooler - Remove and Install
CAT Water Delivery System (WDS) and 777G WTR OEM Off-Highway Truck/Tractor Hydraulic Tank - Remove and Install