Piston and Rings
Show/hide table
Illustration 1 | g03369762 |
Show/hide table
Specification for 384-4314 Piston and Rod Gp | |||
Item | Qty | Part | Specification Description |
1 | 1 | 434-9020 Piston Ring | Install with side marked "UP-1" toward top of the piston. |
Thickness of new top piston ring is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
2 | 1 | 331-6025 Piston Ring | Install with side marked "UP-1" toward top of the piston. |
Thickness of new piston ring is |
|||
Width of the groove in the piston is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
Increase in clearance for each |
|||
3 | 1 | 265-1113 Piston Ring | The ends of the spring coil should be placed 180 degrees from the end gap of the oil control piston rings. The green colored stripe in the spring coil must be visible at the oil control piston ring end gap. |
Thickness of new oil control piston ring is |
|||
Width of the groove in the piston is |
|||
Clearance of the ends when assembled in a new cylinder liner of bore |
|||
Increase in clearance for each |
|||
- | After installing the piston rings, rotate the piston rings so that the end gaps are placed at 120 degrees distance from each other. | ||
Lubricate the entire piston to 360° in zone (C) prior to assembly into the cylinder block. Use clean engine oil. | |||
4 | 1 | 197-9327 Piston Pin | Thoroughly lubricate the piston pin with clean engine oil prior to assembly. |
Diameter is |
|||
Bore (D) is |
Caterpillar Information System:
3500B Locomotive Engines Air Lines
C9.3 Tier 4 Final Engines Camshaft
C9.3 Tier 4 Final Engines Exhaust Lines (DPF Inlet)
C9.3 Tier 4 Final Engines Exhaust Combustion (ARD)
3500B Generator Set Engines Radiator
C13, C15, and C18 Tier 4 Final Engines Exhaust Combustion (ARD)
3500B Locomotive Engines Turbocharger
966M Tier 4 and 972M Tier 4 Wheel Loaders Power Train Transmission Planetary - Assemble
G3512H and G3516H Generator Set Engines Accessory Drive (Front) - Disassemble
374F Excavator Hydraulic System Electronic Control (Main Control Valve)
374F Excavator Hydraulic System General Information (Main Control Valve)
374F Excavator Hydraulic System Boom Cylinder
C9.3 Tier 4 Final Engines Temperature Sensor (DPF Inlet, Flame Detect)
C9.3 Tier 4 Final Engines Diesel Particulate Filter
C9.3 Tier 4 Final Engines Diesel Particulate Filter
C4.4 and C7.1 Engines Idle Validation - Test
C9.3 Tier 4 Final Engines Diesel Particulate Filter
3500B Generator Set Engines Engine Design
G3512H and G3516H Generator Set Engines Accessory Drive (Front) - Assemble
2013/05/13 A New Water Seal Assembly Is Now Used on All 3408, 3412, C27 and C32 Commercial Engines {1100, 7555}
G3512H and G3516H Generator Set Engines Engine Speed Sensor - Remove and Install
2013/08/21 A New Lifter Assembly Is Used for G3500 Engines {1209}
2013/04/17 Inspection of Auto-transformers May Resolve Ground Current Loop Issue On Certain UPSB 130 Uninterruptible Power Supply {1409, 4480}
349F and 352F Excavators Hydraulic System Operational Checks