How to Log On
Overview
You can use either a local (serial) connection, or a remote (Telnet or SSH) connection with a computer on the same network as the Network Management Card to access the "Command Line" interface.
Use case-sensitive user name and password entries to log on (by default, cat and cat for an Administrator, or device and cat for a Device User). A Read-Only User cannot access the "Command Line" interface.
ReferenceIf you cannot remember your user name or password, see the "How to Recover from a Lost Password" section in the, "General Information" chapter of this manual.
Remote Access to the Command Line Interface
You can access the "Command Line" interface through Telnet or SSH. Telnet is enabled by default. Enabling SSH disables Telnet.
To enable or disable these access methods, use the "Web interface". On the "Administration" tab, select "Network" on the top menu bar, and then the access option under "Console" on the left navigation menu.
Telnet for Basic Access
Telnet provides the basic security of authentication by user name and password, but not the high-security benefits of encryption.
To use Telnet, to access the "Command Line" interface:
- From a computer that has access to network on which the Management Card is installed, at a command prompt, type telnet, and the IP address for the Management Card (for example, telnet 139.225.6.133, when the Management Card uses the default Telnet port of 23), and press "ENTER".
If the Management Card uses a non-default port number from 5000 to 32768. A colon or a space must be included, depending on your Telnet client, between the IP address (or DNS name) and the port number. These are commands for general usage: some clients do not allow you to specify the port as an argument and some types of Linux might want extra commands.
- Enter the user name and password (by default, cat and cat for an Administrator, or device and cat for a Device User).
SSH for High-Security Access
If you use the high security of SSL for the "Web interface", use SSH for access to the" Command Line" interface. SSH encrypts user names, passwords, and transmitted data. The interface, user accounts, and user access rights are the same whether you access the "Command Line" interface through SSH or Telnet, but to use SSH, first configure SSH and have an SSH client program installed on your computer.
Local Access to the Command Line Interface
For local access, use a computer that connects to the Network Management Card through the serial port to access the "Command Line" interface:
- Select a serial port at the computer and disable any service that uses the port.
- Connect the provided serial cable from the selected port on the computer to the configuration port at the Management Card.
- Run a terminal program, and configure the selected port for 9600 bps, eight data bits, no parity, one stop bit, and no flow control.
- Press "ENTER". At the prompts, enter your user name and password.
Main Screen
Sample Main Screen
Illustration 1 is an example of the screen displayed when you log on to the "Command Line" interface at the NMC.
 | |
| Illustration 1 | g02552117 |
Information and Status Fields
Main Screen Information Fields
- Two fields identify the operating system (AOS) and application (APP) firmware versions. The application firmware name identifies the device that connects to the network through this NMC.
"AOS vx.x.x"
"APP vx.x.x"
- Three fields identify the system name, contact person, and location of the NMC. (In the" Web interface", select the "Administration" tab, "General" in the top menu bar, and "Identification" in the left navigation menu to set these values.)
"Name : Test Lab"
"Contact: Don Adams"
"Location: Building 3"
- The Up Time field reports how long the NMC has been running since last turn on or reset.
"Up Time: 0 Days 21 Hours 21 Minutes"
- Two fields report when you logged in, by date and time.
"Date : 10/30/2009"
"Time : 5:58:30"
- The "User" field reports whether you logged in through the "Administrator" or "Device Manager" account. (The "Read Only User" account cannot access the "Command Line" interface.) When you log on as Device Manager (equivalent to Device User in the "Web interface"), you can access the event log, configure some UPS settings, and view the number of active alarms.
"User : Administrator"
Main Screen Status Fields
- The Stat field reports the NMC status. The middle status varies according to whether you are running IPv4, IPv6, or both.
"Stat : P+ N+ A+"
| P+ | The operating system (AOS) is functioning properly. |
| IPv4 only | IPv6 only | IPv4 and IPv6 (1) | Description |
| N+ | N6+ | N4+ N6+ | The network is functioning properly. |
| N? | N6? | N4? N6? | A BOOTP request cycle is in progress. |
| N- | N6- | N4- N6- | The NMC failed to connect to the network. |
| N! | N6! | N4! N6! | Another device is using the IP address of the NMC. |
| ( 1 ) | The N4 and N6 values can be different from one another: you could, for example, have N4- N6+. |
| A+ | The application is functioning properly. |
| A- | The application has a bad checksum. |
| A? | The application is initializing. |
| A! | The application is not compatible with the AOS. |
Note: To view the status of the UPS, type ups -st.
How to Use the Command Line Interface
Overview
The "Command Line" interface provides options to configure the network settings and manage the UPS and NMC.
How to Enter Commands
At the "Command Line" interface, use commands to configure the NMC. To use a command, type the command and press "ENTER". Commands and arguments are valid in lowercase, uppercase, or mixed case. Options are case-sensitive.
While using the "Command Line" interface, you can also do the following:
- Type "?" and press "ENTER" to view a list of available commands, based on your account type.
To obtain information about the purpose and syntax of a specified command, type the command, a space, and "?" or the word help. For example, to view "RADIUS" configuration options, type:
"radius ?"
or
"radius help"
- Press the "UP" arrow key to view the command that was entered most recently in the session. Use the "UP" and "DOWN" arrow keys to scroll through a list of up to ten previous commands.
- Type at least one letter of a command and press the "TAB" key to scroll through a list of valid commands that match the text you typed in the "Command Line".
- Type ups "-st" to view the status of the UPS.
- Type "exit" or "quit" to close the connection to the "Command Line" interface.
Command Syntax
| Item | Description |
| - | Options are preceded by a hyphen. |
| <> | Definitions of options are enclosed in angle brackets. (1) |
| [ ] | If a command accepts multiple options or an option accepts mutually exclusive arguments, the values may be enclosed in brackets. |
| l | A vertical line between items enclosed in brackets or angle brackets indicates that the items are mutually exclusive. Use of one of the items is a must. |
| ( 1 ) | For example: -dp <device password> |
Syntax Examples
A command that supports multiple options:
user [ -an <admin name> ] [ -ap <admin password> ]
In this example, the user command accepts the option "-an", which defines the Administrator user name, and the option "-ap", which defines the Administrator password. To change the Administrator user name and password to "XYZ":
- Type the "user" command, one option, and the argument "XYZ":
"user -ap XYZ"
- After the first command succeeds, type the "user" command, the second option, and the argument "XYZ":
"user -an XYZ"
A command that accepts mutually exclusive arguments for an option:
"alarmcount -p [ all Iwarning Icritical ]"
In this example, the option "-p" accepts only three arguments: all, warning, or critical. For example, to view the number of active critical alarms, type:
"alarmcount -p critical"
The command will fail if you type an argument that is not specified.
Command Response Codes
The command response codes enable scripted operations to detect error conditions reliably without having to match error message text.
The CLI reports all command operations with the following format:
"E [0–9] [0–9] [0–9] : Error message"
| Code | Error message |
| E000 | Success |
| E001 | Successfully Issued |
| E002 | Reboot required for change to take effect |
| E100 | Command failed |
| E101 | Command not found |
| E102 | Parameter Error |
| E103 | "Command Line" Error |
| E104 | User Level Denial |
| E105 | Command Prefill |
| E106 | Data Not Available |
| E107 | Serial communication with the UPS has been lost |
Command Descriptions
?
Access - Administrator, Device User
Description - View a list of all the CLI commands available to your account type. To view help text for a specific command, type the command followed by a question mark.
Example - To view a list of options that are accepted by the "alarmcount" command, type:
"alarmcount ?"
about
Access - Administrator, Device User
Description - View hardware and firmware information. This information is useful in troubleshooting and enables you to determine if updated firmware is available.
alarmcount
Access - Administrator, Device User
Description -
| Option | Arguments | Description |
| -p | all | View the number of active alarms reported by the NMC. Information about the alarms is provided in the event log. |
| warning | View the number of active warning alarms. | |
| critical | View the number of active critical alarms. |
Example - To view all active warning alarms, type:
"alarmcount -p warning"
boot
Access - Administrator only
Description - Define how the NMC will obtain network settings, including the IP address, subnet mask, and default gateway. Then configure the BOOTP or DHCP server settings.
| Option | Argument | Description |
| -b <boot mode> | dhcp l bootp l manual | Define how the TCP/IP settings will be configured when the NMC turns on, resets, or restarts. Refer to the "TCP/IP and Communication Settings" section in the, "Administration:Network Features" chapter of this manual. |
| -c | enable l disable | dhcp boot modes only. Enable or disable the requirement that the DHCP server provides the cookie. |
| The default values for these three settings do not need changing: -v <vendor class> : -i <client id> : The MAC address of the NMC, which uniquely identifies the NMC on the network -u <user class> :The name of the application firmware module |
||
Example - To use a DHCP server, to obtain network settings:
- Type "boot -b dhcp"
- Enable the requirement that the DHCP server provides the cookie:
"boot -c enable"
cd
Access - Administrator, Device User
Description - Navigate to a folder in the directory structure of the NMC.
Example 1 - To change to the ssh folder, and confirm that an SSH security certificate was uploaded to the NMC:
- Type "cd ssh" and press "ENTER".
- Type "dir" and press "ENTER" to list the files stored in the SSH folder.
Example 2 - To return to the main directory folder, type:
"cd .."
console
Access - Administrator only
Description - Define whether users can access the command line interface using Telnet, which is enabled by default, or Secure SHell (SSH), which provides protection by transmitting user names, passwords, and data in encrypted form. You can change the Telnet or SSH port setting for additional security. Alternately, disable network access to the command line interface.
| Option | Argument | Description |
| -S | disable I telnet l ssh | Configure access to the command line interface, or use the disable command to prevent access.. Enabling SSH enables SCP and disables Telnet. |
| -pt | <telnet port n> | Define the Telnet port used to communicate with the NMC (23 by default). |
| -ps | <SSH port n> | Define the SSH port used to communicate with the NMC (22 by default). |
| -b | 2400 l 9600 l 19200 l 38400 | Configure the speed of the serial port connection (9600 bps by default). |
Example 1 - To enable SSH access to the command line interface, type:
"console -S ssh"
Example 2 - To change the Telnet port to 5000, type:
"console -pt 5000"
date
Access - Administrator only
Description - Configure the date used by the NMC.
ReferenceTo configure an NTP server to define the date and time for the NMC, refer to the "Set the Date and Time" section in the, "Administration: General Options" chapter of this manual.
| Option | Argument | Description |
| -d | <datestring> | Set the current date. Use the date format specified by the date -f command. |
| -t | <00:00:00> | Configure the current time, in hours, minutes, and seconds. Use the 24-hour clock format. |
| -f | mm/dd/yy l dd.mm.yyyy l mm-dd-yy l dd-mm-yy l yyyy-mm-dd | Select the numerical format in which to display all dates in this user interface. Each letter m (for month), d (for day), and y (for year) represents one digit. Single-digit days and months are displayed with a leading zero. |
| -z | <time zone offset> | Set the difference with GMT in order to specify your time zone. Enables you to synchronize with other people in different time zones. |
Example 1 - To display the date using the format yyyy-mm-dd, type:
"date -f yyyy-mm-dd"
Example 2 - To define the date as October 30, 2009, using the format configured in the preceding example, type:
"date -d 2009-10-30"
Example 3 - To define the time as 5:21:03 p.m., type:
"date -t 17:21:03"
delete
Access - Administrator only
Description - Delete the event or data log, or delete a file in the file system.
| Argument | Description |
| <file name> | Type the name of the file to delete. |
Example - To delete the event log:
- Navigate to the folder that contains the file to delete. For example, to navigate to the "logs" folder, type:
"cd logs"
- To view the files in the logs folder, type:
"dir"
The file event ".txt" is listed.
- Type
"delete event.txt."
dir
Access - Administrator, Device User
Description - View the files and folders stored on the NMC.
dns
Access - Administrator
Description - Configure the manual Domain Name System (DNS) settings.
| Parameter | Argument | Description |
| -OM | enable l disable | Override the manual DNS. |
| -p | <primary DNS server> | Set the primary DNS server. |
| -s | <secondary DNS server> | Set the secondary DNS server. |
| -d | <domain name> | Set the domain name. |
| -n | <domain name IPv6> | Set the domain name IPv6. |
| -h | <host name> | Set the host name. |
eventlog
Access - Administrator, Device User
Description - View the date and time you retrieved the event log, the status of the UPS, and the status of sensors connected to the NMC. View the most recent device events, and the date and time the event occurred. Use the following keys to navigate the event log:
| Key | Description |
| ESC | Close the event log and return to the command line interface. |
| ENTER | Update the log display. Use this command to view events that were recorded after you last retrieved and displayed the log. |
| SPACEBAR | View the next page of the event log. |
| B | View the preceding page of the event log. This command is not available at the main page of the event log. |
| D | Delete the event log. Follow the prompts to confirm or deny the deletion. Deleted events cannot be retrieved. |
exit
Access - Administrator, Device User
Description - Exit from the command line interface session.
format
Access - Administrator only
Description - Reformat the file system of the NMC and erase all security certificates, encryption keys, configuration settings, and the event and data logs. Be careful with this command.
Note: To reset the NMC to the default configuration, use the "resetToDef" command.
FTP
Access - Administrator only
Description - Enable or disable access to the FTP server. Optionally, change the port setting to the number of any unused port from 5001 to 32768 for added security.
| Option | Argument | Definition |
| -p | <port number> | Define the TCP/IP port that the FTP server uses to communicate with the NMC (21 by default). The FTP server uses both the specified port and the port one number lower than the specified port. |
| -S | enable l disable | Configure access to the FTP server. |
Example - To change the TCP/IP port to 5001, type:
"ftp -p 5001"
help
Access - Administrator, Device User
Description - View a list of all the CLI commands available to your account type. To view help text for a specific command, type the command followed by "help".
Example 1 - To view a list of commands available to someone logged on as a Device User, type:
"help"
Example 2 - To view a list of options that are accepted by the "alarmcount" command, type:
"alarmcount help"
netstat
Access - Administrator, Device User
Description - View the status of the network and all active IPv4 and IPv6 addresses.
ntp
Access - Administrator, Device User
Description - View and configure the network time protocol parameters.
| Option | Argument | Definition |
| -OM | enable l disable | Override the manual settings. |
| -p | <primary NTP server> | Specify the primary server. |
| -s | <secondary NTP server> | Specify the secondary server. |
Example 1 - To enable the override of manual setting, type:
"ntp -OM enable"
Example 2 - To specify the primary NTP server, type:
"ntp -p 150.250.6.10"
ping
Access - Administrator, Device User
Description - Determine whether the device with the IP address or DNS name you specify is connected to the network. Four inquiries are sent to the address.
| Argument | Description |
| <IP address or DNS name> | Type an IP address with the format xxx.xxx.xxx.xxx, or the DNS name configured by the DNS server. |
Example - To determine whether a device with an IP address of 150.250.6.10 is connected to the network, type:
"ping 150.250.6.10"
portSpeed
Access - Administrator
Description -
| Option | Arguments | Description |
| -s | auto l 10H l 10F l 100H l 100F | Define the communication speed of the Ethernet port. The "auto" command enables the Ethernet devices to negotiate to transmit at the highest possible speed. Refer to the "Port Speed" section in the, "Administration : Network Features" chapter of this manual for more information about the port speed settings. |
Example - To configure the TCP/IP port to communicate using 100 Mbps with half-duplex communication (communication in only one direction at a time), type:
"portspeed -s 100H"
prompt
Access - Administrator, Device User
Description - Configure the command line interface prompt to include or exclude the account type of the currently logged-in user. Any user can change this setting, all user accounts will be updated to use the new setting.
| Option | Argument | Description |
| -s | long | The prompt includes the account type of the currently logged-in user. |
| short | The default setting. The prompt is four characters long. |
Example - To include the account type of the currently logged-in user in the command prompt, type:
"prompt -s long"
quit
Access - Administrator, Device User
Description - Exit from the command line interface session ( works the same as the exit command).
radius
Access - Administrator only
Description - View the existing RADIUS settings, enable or disable RADIUS authentication, and configure basic authentication parameters for up to two RADIUS servers.
ReferenceFor a summary of RADIUS server configuration and a list of supported RADIUS servers, refer to the "Configuring the RADIUS Server" section in the, "Administration : Security" chapter of this manual.
Additional authentication parameters for RADIUS servers are available at the" Web interface" of the NMC.
| Option | Argument | Description |
| -a | local l radiusLocal l radius | -Configure RADIUS authentication: "local" - RADIUS is disabled. Local authentication is enabled. "radiusLocal" - RADIUS, then Local Authentication. RADIUS and local authentication are enabled. Authentication is requested from the RADIUS server first. If the RADIUS server fails to respond, local authentication is used. "radius" - RADIUS is enabled. Local authentication is disabled. |
| -p1 -p2 |
<server IP> | The server name or IP address of the primary or secondary RADIUS server (1) |
| -s1 -s2 |
<server secret> | The shared secret between the primary or secondary RADIUS server and the NMC. |
| -t1 -t2 |
<server timeout> | The time in seconds that the NMC waits for a response from the primary or secondary RADIUS server. |
| ( 1 ) | RADIUS servers use port 1812 by default to authenticate users. To use a different port, add a colon followed by the new port number to the end of the RADIUS server name or IP address. |
Example 1 - To view the existing RADIUS settings for the NMC, type "radius" and press "ENTER".
Example 2 - To enable RADIUS and local authentication, type:
"radius -a radiusLocal"
Example 3 - To configure a 10 - second timeout for a secondary RADIUS server, type:
"radius -t2 10"
reboot
Access - Administrator
Description - Restart the interface of the NMC.
resetToDef
Access - Administrator only
Description - Reset all parameters to default.
| Option | Arguments | Description |
| -p | all l keepip | Reset all configuration changes, including event actions, device settings, and, optionally, TCP/IP configuration settings. |
Example - To reset all of the configuration changes except the TCP/IP settings for the NMC, type:
"resetToDef -p keepip"
snmp, snmp3
Access - Administrator only
Description - Enable or disable SNMP 1 or SNMP 3.
| Option | Arguments | Description |
| -S | enable l disable | Enable or display the respective version of SNMP, 1 or 3. |
Example - To enable SNMP version 1, type:
"snmp -S enable"
system
Access - Administrator only
Description - View and set the system name, the contact, the location and view up time as well as the date and time, the logged-on user, and the high-level system status P, N, A.
| Option | Arguments | Description |
| -n | <system name> | Define the device name, the name of the person responsible for the device, and the physical location of the device. Note: If you define a value with more than one word, the value in quotation marks must be enclosed. These values are also used by InfraStruxure Central and the NMCs SNMP agent. |
| -c | <system contact> | |
| -l | <system location> |
Example 1 - To set the device location as "Test Lab", type:
"system -l Test Lab"
Example 2 - To set the system name as "Don Adams", type:
"system -n Don Adams"
tcpip
Access - Administrator only
Description - View and manually configure these network settings for the NMC:
| Option | Arguments | Description |
| -i | <IP address> | Type the IP address of the NMC, using the format xxx.xxx.xxx.xxx |
| -s | <subnet mask> | Type the subnet mask for the NMC. |
| -g | <gateway> | Type the IP address of the default gateway. Do not use the loopback address (127.0.0.1) as the default gateway. |
| -d | <domain name> | Type the DNS name configured by the DNS server. |
| -h | <host name> | Type the host name that the NMC will use. |
Example 1 - To view the network settings of the NMC, type "tcpip" and press "ENTER".
Example 2 - To configure an IP address of "150.250.6.10"manually for the NMC, type:
"tcpip -i 150.250.6.10"
tcpip6
Access - Administrator only
Description - Enable IPv6 and view and manually configure these network settings for the NMC (NMC):
| Option | Argument | Description |
| -S | enable l disable | Enable or disable IPv6. |
| -man | enable l disable | Enable manual addressing for the IPv6 address of the NMC. |
| -auto | enable l disable | Enable the NMC to configure the IPv6 address automatically. |
| -i | <IPv6 address> | Set the IPv6 address of the NMC. |
| -g | <IPv6 gateway> | Set the IPv6 address of the default gateway. |
| -d6 | router l stateful l stateless l never | Set the DHCPv6 mode, with parameters of router controlled, stateful (for address and other information, to maintain status), stateless (for information other than address, the status is not maintained ), never. |
Example 1 - To view the network settings of the NMC, type "tcpip6" and press "ENTER".
Example 2 - To configure an IPv6 address of "2001:0:0:0:0:FFD3:0:57ab"manually for the NMC, type:
"tcpip -i 2001:0:0:0:0:FFD3:0:57ab"
uio
Access - Administrator, Device User
Description - This command is available for an Network Management Card With Environmental Monitoring with a connected Dry Contact I/O Accessory
| Option | Argument | Description |
| -rc <UIO port #> | open l close | Change the state of a connected output, and specify the UIO (universal input/ output) port number. |
| -st | <UIO port #> l <UIO port #>, <UIO port #> l <UIO port #>_<UIO port #> |
View the status of the sensors connected to the Dry Contact I/O Accessory. To view the status of a specific sensor or several sensors, type the UIO port numbers. |
| -disc | <UIO port #> l <UIO port #>, <UIO port #> l <UIO port #> _ <UIO port #> |
Identify new input contact or output relay connections. |
Example 1 - To open the output, type:
"uio -rc 2 open"
Example 2 - To view the status of the devices connected to a Dry Contact I/O Accessory that is installed in universal input/ output port 2, type:
"uio -st 2"
ups
Note: Some ups options are dependent on the UPS model. Not all configurations may support all options of the ups command.
Access - Administrator, Device User
Description - Control the UPS and view status information.
| Option | Arguments | Description |
| -c | off l graceoff l on l reboot l gracereboot l sleep l gracesleep | Configure UPS actions. Refer to the "Actions (for a single UPS and Synchronized Control Groups)" section in the, "UPS Monitor and Configure" chapter of this manual for detailed information. |
| -r | start l stop | Initiate or end a runtime calibration. A calibration recalculates remaining runtime and requires the following: Because a calibration temporarily depletes the UPS batteries, you can perform a calibration only if battery capacity is at 100 percent. For some UPSs, the load must be at least 7 percent to perform a calibration. |
| -s | start | Initiate a UPS self-test. |
| -b | enter l exit | Control the use of bypass mode. This command is model-specific and may not apply to your UPS. Refer to the "Actions (for a single UPS and Synchronized Control Groups)" section in the, "UPS Monitor and Configure" chapter of this manual for detailed information. |
| -o# | off l delayoff l on l delay on l reboot l delayreboot | For information about outlet groups, refer to the "Outlet Groups" section in the, "UPS Monitor and Configure" chapter of this manual. When the state of the outlet group is on, the option accepts three arguments: "off" - Turn off the group immediately. "delayoff" - Turn off the group after the number of seconds configured as Power Off Delay. "reboot" - Turn off the group immediately, then turn on after the number of seconds configured as Reboot Duration and Power On Delay. "delayreboot" - Turn off the outlet group after the number of seconds configured as Power Off Delay, then turn on after the number of seconds configured as Reboot Duration and Power On Delay. When the state of the outlet group is off, the option accepts two arguments: "on" - Turn on the group immediately. "delayon" - Turn on the group after the number of seconds configured as Power On Delay. The Power On Delay, Power Off Delay, and Reboot Duration must be configured at the "Web interface". |
| -os# | View the status (on, off, or rebooting) of all of the outlet groups. To view the status of a specific outlet group, specify the number. For example, type ups "-os1" to view the status of outlet group 1. | |
| -st | View the status of the UPS. |
Example - To initiate a runtime calibration, type:
"ups -r start"
user
Access - Administrator only
Description - Configure the user name and password for each account type, and configure the inactivity timeout.
ReferenceFor information on the permissions granted to each account type (Administrator, Device User, and Read-Only User), refer to the "Types of user accounts" in the, "General Information" chapter of this manual.
| Option | Argument | Description |
| -an -dn -rn |
<admin name> <device name> <read-only name> |
Set the case-sensitive user name for each account type. The maximum length is ten characters. |
| -ap -dp -rp |
<admin password> <device password> <read-only password> |
Set the case-sensitive password for each account type. The maximum length is 32 characters. Blank passwords (passwords with no characters) are not allowed. |
| -t | <minutes> | Configure the time (3 minutes by default) that the system waits before logging off an inactive user. |
Example 1 - To change the Administrator user name to XYZ, type:
"user -an XYZ"
Example 2 - To change the log-off time to 10 minutes, type:
"user -t 10"
web
Access - Administrator
Description - Enable access to the "Web interface" using HTTP or HTTPS.
For additional security, you can change the port setting for HTTP and HTTPS to any unused port from 5000 – 32768. Users must then use a colon in the address field of the browser to specify the port number. For example, for a port number of 5000 and an IP address of 152.214.12.114: "http://152.214.12.114:5000"
| Option | Argument | Definition |
| -S | disable l http l https | Configure access to the" Web interface". When HTTPS is enabled, data is encrypted during transmission and authenticated by digital certificate. |
| -ph | <http port #> | Specify the TCP/IP port used by HTTP to communicate with the NMC (80 by default). |
| -ps | <http port #> | Specify the TCP/IP port used by HTTPS to communicate with the NMC (443 by default). |
Example - To prevent all access to the "Web interface", type:
"web -S disable"
xferINI
Access - Administrator only. This command only works through serial CLI.
Description - Use XMODEM to upload an .ini file while you are accessing the command line interface through a serial connection. After the upload completes:
- If there are any system or network changes, the command line interface restarts, and log on again.
- If you selected a baud rate for the file transfer that is not the same as the default baud rate for the NMC, reset the baud rate to the default to re-establish communication with the NMC.
xferStatus
Access - Administrator only
Description - View the result of the last file transfer.