Engine Oil Scavenge Pump
Show/hide table
图 1 | g01471861 |
Show/hide table
注意 |
---|
操作之前,必须使用干净的发动机机油润滑泵体,并且泵必须能灵活运转,否则就会导致部件的损坏。 |
Show/hide table
技术规格 - 8N-9164 发动机扫油泵 | |||
项目 | 数量 | 零件 | 技术规格说明 |
A | 1 | 7N-5052 齿轮 | 长度为 |
扫油泵体中新齿轮孔的深度为 |
|||
B | 1 | 161-2509 驱动轴 | 直径为 |
安装前衬套中新驱动轴的孔径为 |
|||
C | - | - | 自惰轮轴组件末端至齿轮端面的距离为 |
D | 1 | 1W-6005 衬套 | 2W-6895 扫油泵泵体中的安装深度为 |
E | 1 | 7W-1017 轴 | 直径为 |
安装前衬套上新惰轮轴的孔径为 |
|||
1 | 1 | 0S-0484 螺栓 | 采用下述步骤拧紧螺栓: |
将驱动齿轮安装到驱动轴组件前,清洁轴和齿轮孔。 | |||
1. 敲打驱动齿轮以座合驱动齿轮的锥形部分。 | |||
2. 拧紧螺栓至扭矩 |
|||
3. 重复此步骤直到扭矩不再变化。 |
Show/hide table
图 2 | g02596558 |
Show/hide table
技术规格 - 8N-9164 发动机扫油泵 | |||
项目 | 数量 | 零件 | 技术规格说明 |
F | - | - | 从中线穿过轴承孔的衬套接头位置为 45 ± 15 度。 |
G | 2 | 4M-3248 空心定位销 | 空心定位销的延伸长度为 |
H | 2 | 1W-6005 衬套 | 7N-8814 扫油泵盖上的衬套安装深度为 |
Caterpillar Information System:
336F MHPU Mobile Hydraulic Power Unit Machine System Specifications Relief Valve (Main) - Heavy Lift
Crimping Caterpillar 1E294, 1E716, 1E844 Hose and Couplings {0374, 0599, 0684, 0738, 5057} Crimping Caterpillar 1E294, 1E716, 1E844 Hose and Couplings {0374, 0599, 0684, 0738, 5057}
C32 Marine Generator Set Alarms and Shutoffs
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Advanced Preventive Maintenance
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Basic Preventive Maintenance
UPSB505 Uninterruptible Power Supply UPS Battery - 50Hz Troubleshooting
Cat Water Delivery System (WDS) System Pressure Release
3500 Engines Engine Oil Pan
C175-16 and C175-20 Generator Set Engines Air Cleaner
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Twin Secondary Fuel Filter
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Stick Lines - Quick Coupler
C4.4 Industrial Engine Fuel Temperature Sensor - Remove and Install
C3.4B Industrial Engine Engine Oil and Filter - Change
C3.4B Industrial Engine Fuel System Primary Filter (Water Separator) Element - Replace
C32 Marine Generator Set Refill Capacities
3512C Oil Well Service Engines Configuration Parameters
3512C Oil Well Service Engines Aftercooler Core - Inspect/Clean/Test
C32 Marine Generator Set Engine Oil Sample - Obtain
374F Excavator Machine System Hydraulic Pedal Control (Auxiliary)
3500 Engines Turbocharger
C3.4B Industrial Engine Fuel System Secondary Filter - Replace
2011/06/10 Procedure for Releasing Stuck Buttons Due to Rapid Altitude Changes for Certain Advisor Displays {7490}
2011/06/08 A New Valve Lifter As is now Available on Certain 3412 Marine Engines {1102, 1121, 1123, 1209}
C32 Marine Generator Set Belts - Inspect/Adjust/Replace