A New Flange Is Used for the Water Lines Group on C175-16 Generator Set Engines {1355, 1380, 1393}
- Generator Set:
- C175-16 (S/N: WYB1-UP)
Description of Change: The new flanges do not have any welded joints.
Adaptable To:
Show/hide table
Illustration 1 | g02350766 |
(1) 6V-5815 Bolt (2) 6V-5839 Washer (3) 344-9288 Flange (4) 344-9286 Ring |
The former 108-6170 Clamp As is replaced with new 344-9288 Flange and the former 6V-4248 Bolt is replaced with the new 6V-5815 Bolt in the 254-5910 Water Lines Gp .
The new 344-9288 Flange is adaptable to C175-16 Generator Set Engines back to first production.
The new 344-9288 Flange is effective with WYB00375-UP.
Show/hide table
Required Parts List     | |||
Item     | Qty     | Part Number     | Description     |
1     | 2     | 6V-5815     | Bolt     |
2     | 2     | 6V-5839     | Washer     |
3     | 1     | 344-9288     | Flange     |
4     | 1     | 344-9286     | Ring     |
Caterpillar Information System:
CG137-08 and CG137-12 Industrial Engines Electrical Connectors
CG137-08 and CG137-12 Industrial Engines Electronic Control System Components
C4.4 Industrial Engine Aftercooler Core - Inspect
C27 Petroleum Engine Inlet and Exhaust Valve Springs - Remove and Install
Installing an Automatic Stationary Regeneration Switch on Certain On-highway Engines{108F, 7332} Installing an Automatic Stationary Regeneration Switch on Certain On-highway Engines{108F, 7332}
C15 and C18 Engines for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Outlet Pressure
C15 and C18 Engines for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure
2010/12/08 An Improvement has been Made to Reduce the Amount of Radial Play of the Front Linkage Pin on Certain Excavators {6501, 6502, 6513}
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Pressure Switch (Refrigerant Pressure Cutoff)
C15 and C18 Industrial Engines Pistons and Connecting Rods - Remove and Install
C27 and C32 Engines Exhaust Elbow - Remove and Install - Clean Emissions Module Inlet
3516B Marine Auxiliary Engine Cat Data Link - Test
3516B Marine Auxiliary Engine Speed/Timing - Test
CG137-08 and CG137-12 Industrial Engines Electronic Control Module (ECM)
320E and 323E Excavators Hydraulic System Final Drive
C9 On-highway Engines Air Compressor - Check
C9 On-highway Engines Belt Tensioner - Check - If Equipped
C9 On-highway Engines Belts - Inspect/Adjust/Replace
2010/11/29 Torque and Sealant Requirements for Coolant Level Sensor on Certain Cat Engines {7422}
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Control Module
320E and 323E Excavators Fuel Lift Pump Strainer - Replace
C9 On-highway Engines Coolant (DEAC) - Change
3406C Industrial Engine Coolant Level - Check
C7.1 Industrial Engine Radiator Restrictions