Idler Gear - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 9U-7336     | 壳体     | 1     |
5P-7306 | 发动机盘车工具     | 1     | |
B     | 364-9107     | 正时销 (喷油泵)     |
1     |
C     | 230-6284     | 正时销(凸轮轴)     | 1     |
D     | 136-4632     | 正时销(曲轴)     | 1     |
268-1966 | 适配器     | 1     | |
E     | 298-5564     | T40 Torx 套筒     | 1     |
开始:
- 拆下前盖。 请参阅拆解和组装, "前盖 - 拆卸和安装"以了解正确步骤。
- 拆下气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
注: 必须小心操作,确保在燃油泵齿轮的拆卸过程中不会改变燃油泵正时。 小心地按照本步骤拆卸燃油泵齿轮。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将螺塞 (1) 从缸体上拆下,然后将 O 形密封圈 (2) 从螺塞上拆下。
Show/hide table
图 1 | g02485936 |
Show/hide table
图 2 | g01994553 |
- 使用工具 (A) 转动曲轴,使 1 号活塞处于其压缩冲程的上止点位置。 有关正确的步骤,请参阅系统操作、测试和调整, "查找 1 号活塞上止点位置"。
- 穿过孔 (W) 安装工具 (D) ,以便锁定曲轴,使 1 号活塞处于压缩冲程上止点位置。
- 确保已将工具 (C) 安装在凸轮轴齿轮 (3) 的孔 (X) 中。 使用工具 (C) ,将凸轮轴锁定到位。
注: 确保标记齿轮,以便显示对准位置。 参考图 2。
- 使用工具 (B) 将燃油喷油泵齿轮锁定在正确的位置。 有关正确的步骤,请参考拆解和组装, "燃油喷油泵 - 拆卸"。
- 使用工具 (E) 松开所有摇臂 (6) 上的螺纹座圈 (5) 。 拧松所有摇臂 (6) 上的螺纹座圈 (5) ,直到所有气门完全闭合。
注: 如果不能保证完全拧松所有螺纹座圈,可能会导致气门与活塞接触。
Show/hide table
图 3 | g01994556 |
- 标记盘 (8) ,以便显示方向。
注: 识别标记能确保将板安装在原来的对准位置。
Show/hide table
图 4 | g01994576 |
Show/hide table
图 5 | g01994557 |
- 拆下螺栓 (7) 。
- 拆下板 (8) 。
- 拆下惰轮组件 (4) 。
- 将轮毂 (9) 从前壳体的凹槽中拆下。
Caterpillar Information System:
C4.4 Industrial Engine Idler Gear - Install
C4.4 Industrial Engine Housing (Front) - Remove
C4.4 Industrial Engine Housing (Front) - Remove - Heavy Duty Housing (Front)
C4.4 Industrial Engine Housing (Front) - Install
C4.4 Industrial Engine Housing (Front) - Install - Heavy Duty Housing (Front)
C4.4 Industrial Engine Glow Plugs - Remove and Install
C4.4 Industrial Engine Gear Group (Front) - Remove and Install
C4.4 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Solenoid Valves
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Sensors
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408} Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Switches
C4.4 Industrial Engine Idler Pulley - Remove and Install - Flat Idler Pulley
C4.4 Industrial Engine Idler Pulley - Remove and Install - Grooved Idler Pulley
C6.6 Industrial Engine Front Cover - Remove and Install
C6.6 Industrial Engine Front Cover - Remove and Install - Heavy Duty Front Cover
C4.4 Industrial Engine Inlet Air Control - Install - NRS Induction Mixer
C4.4 Industrial Engine Inlet Air Control - Remove - NRS Induction Mixer
C4.4 Industrial Engine Inlet and Exhaust Valve Springs - Remove and Install
C4.4 Industrial Engine Inlet and Exhaust Valves - Remove and Install
C4.4 Industrial Engine Inlet Manifold Temperature Sensor - Remove and Install
C4.4 Industrial Engine Lifter Group - Remove and Install - Hydraulic Lifter Group
C4.4 Industrial Engine Piston Cooling Jets - Remove and Install
C4.4 Industrial Engine Pistons and Connecting Rods - Assemble