Fuel Injection Pump - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 5P-7306     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 136-4632     | 正时销(曲轴)     | 1     |
268-1966 | 适配器     | 1     | |
C     | 364-9107     | 正时销 (喷油泵)     |
1     |
D     | 370-8376     | 塞和盖     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
开始:
- 拆下曲轴箱呼吸器滤罐和塑料管组件。 有关正确的步骤,请参阅拆解和组装, "曲轴箱呼吸器 - 拆卸"。
注: 可以使用两个工具 (A) 中的任意一个。 请使用最适用的工具。
Show/hide table
接触高压燃油可能导致液体渗透和烧伤危险。 高压燃油溢出可能会产生火灾。 如果不遵循检查、保养和维修指南,可能会造成人身伤亡。 |
Show/hide table
注意 |
---|
请确保对燃油系统进行的所有调整和修理均由经过适当培训的授权人员执行。 在燃油系统上开始任何工作之前,请参阅操作和保养手册, "一般危险信息和高压燃油管路"以了解安全信息。 有关在所有燃油系统工作期间必须遵循的清洁度标准的详细信息,请参阅系统运作,测试和调整, "燃油系统部件清洁度"。 |
- 将燃油供应转到断开位置。
- 将蓄电池断路开关转到断开位置。
- 拆下塞 (11) ,然后拆下 O 形密封圈 (10) (未显示)。
Show/hide table
图 1 | g02482036 |
- 将工具 (C) 安装到喷油泵 (13) 上。
- 使用工具 (A) 转动曲轴,使 1 号活塞处于上止点位置。 请参阅系统操作、测试和调整, "燃油喷射正时 - 检查",以了解正确的步骤。
- 使用工具 (B) 确保曲轴锁定,1 号活塞处于上止点位置。
- 从线束组件 (1) 上切割电缆扎带 (3) 。
- 将线束组件 (1) 从冷却液温度传感器 (2) 上断开。 有关正确步骤,请参阅拆解和装配, "冷却液温度传感器 - 拆卸和安装"。
- 将线束组件 (7) 从燃油歧管中的压力传感器上断开。
- 将线束组件 (16) 从流量控制阀上断开。
- 将线束组件 (14) 从燃油温度传感器上断开。
- 将线束组件 (15) 从发动机机油压力传感器上断开。 有关正确步骤,请参阅拆解和装配, "发动机机油压力传感器 - 拆卸和安装"。
- 将螺栓 (4) 和螺栓 (9) (未显示)从支架 (5) 上拆下。 拆下支架并放到远离喷油泵的位置。
注: 应远离喷油泵定位线束组件,以免妨碍喷油泵的拆卸。
- 清洁喷油泵 (13) 及其周围区域。 开始组装前,确保该区域无污染。
- 将适当的容器放置到燃油喷油泵 (13) 的下方,用来盛装所有可能溢出的燃油。
- 将塑料管组件 (6) 和塑料管组件 (8) 从燃油喷油泵 (13) 上断开。 使用工具 (D) 塞住塑料管组件。 盖住喷油泵上塑料管组件的接头。
- 拆下将喷油泵 (13) 连接到燃油歧管的喷油管 (12) 。 有关正确的步骤,请参阅拆解和组装, "燃油喷油管 - 拆卸"。
- 用工具 (D) 塞住喷油泵和燃油歧管上的开口。 废弃喷油管路。
- 将螺母 (19) 和螺栓 (22) 从喷油泵 (13) 上拆下。 记录不同长度螺栓的位置。
注: 在螺栓拆卸过程中应用手支撑喷油泵。
Show/hide table
图 2 | g02482038 |
- 小心地从前壳体 (20) 卸下喷油泵 (13) 。 确保前壳体 (20) 中的孔在拆卸喷油泵时未损坏。
- 拆下密封垫 (18) 。
- 如有必要,将螺柱 (21) 从前壳体 (20) 上拆下。
Caterpillar Information System:
C4.4 Industrial Engine Fuel Injection Pump - Install
C4.4 Industrial Engine Fuel Injection Lines - Remove
C4.4 Industrial Engine Fuel Injection Lines - Install
C4.4 Industrial Engine Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
C4.4 Industrial Engine Front Cover - Remove and Install
C4.4 Industrial Engine Front Cover - Remove and Install - Heavy Duty Front Cover
C4.4 Industrial Engine Flywheel Housing - Remove and Install - Wet Back End Housing
C9.3 Tier 4 Final Engines Injector Bypass Fuel Flow - Test
C7.1 (Mech) Industrial Engine Cylinder Block
C7.1 (Mech) Industrial Engine Fuel Transfer Pump
C7.1 Engines for Caterpillar Built Machines Main Bearing Journal
C7.1 (Mech) Industrial Engine Fuel Injection Lines
C4.4 Industrial Engine Fuel Injection Pump Gear - Install
C4.4 Industrial Engine Fuel Injection Pump Gear - Remove
C4.4 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C4.4 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
C7.1 (Mech) Industrial Engine Piston and Rings
C7.1 Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Switches
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408} Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Sensors
320E, 320F, 323E, 323F, 324E, 326F, 329E, 329F and 330F Excavators Tool Control System Solenoid Valves
C4.4 Industrial Engine Gear Group (Front) - Remove and Install - Heavy Duty Gear Group (Front)
C4.4 Industrial Engine Gear Group (Front) - Remove and Install