Backlight Is On Continuously
系统运作描述:
Show/hide table
图 1 | g02237982 |
"背光调节"开关是众多带背光的开关之一,位于卡车驾驶室内。 |
注: 如果大灯开关对地短路,背光强度将处于日间模式。 对于带背光的开关,背光强度将保持最大强度。
注: 开始这些步骤前,务必确认所执行工作机器的电气示意图中的触针和导线编号。
该文档中的故障诊断与排除信息也适用于以下开关的背光:"辅助转向测试开关", "经济模式测试开关" 和 "加热式视镜开关"。
通过此步骤,可检查所有类似的摇臂开关 LED 背光回路。 所有背光 LED 指示灯均是摇臂开关的组成部分。 这些指示灯不可更换。
如果卡车钥匙开关转到断开位置时,背光没有熄灭,则执行以下步骤:
测试步骤 1. 确认背光不能熄灭
- 把钥匙开关转到接通位置。
- 将大灯开关转到关闭位置。
- 观察背光。
预期结果:
背光熄灭。
结果:
- 确定 - 背光熄灭。 此时不存在该故障。 允许机器恢复使用。停止
- 异常 - 背光点亮。 转至测试步骤 2。
测试步骤 2. 检查线束中有无短路
- 把钥匙开关转到断开位置。
- 从线束上断开所有相关的 ECM 模块。
- 从大灯开关上断开线束。
- 获得背光回路的触针和导线编号。 确认所执行工作机器的电气示意图中的触针和导线编号。
- 测量大灯开关与相应的 ECM 触点之间的线束电阻。
预期结果:
各个电阻都大于 5000 欧姆。
结果:
- 确定 - 各个电阻都大于 5000 欧姆。 线束中的电路正常。 背光 LED 指示灯可能出现故障。
修复: 更换含有背光 LED 指示灯的摇臂开关。
转至测试步骤 3。
- 异常 - 电阻小于 5 欧姆。 大灯开关线束中存在电路短路。
修复: 修理或更换线束。
转至测试步骤 3。
测试步骤 3. 执行所有工作检查
- 重新连接已拆卸的所有接头。
- 将钥匙开关转到接通位置。
- 将摇臂开关推到接通位置。
- 确认背光点亮。
- 将摇臂开关推到断开位置。
- 确认背光熄灭。
预期结果:
摇臂开关接通时背光点亮,摇臂开关断开时背光熄灭。
结果:
- 确定 - 背光工作正常。 允许机器恢复使用。停止
- 异常 - 背光工作不正常。 ECM 可能有故障,但 ECM 出现故障的可能性不大。
修复: 请联系您代理商的技术通讯员,咨询 Caterpillar 的建议。 如果必须更换 ECM,请参阅本手册中的测试和调整, "电子控制模块(ECM)- 更换"章节。
停止
Caterpillar Information System:
120 and 120 AWD Motor Grader Braking System - Test
C3.4B Engines Diesel Particulate Filter Temperature Is Low
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Advanced Preventive Maintenance
UPSB125 Uninterruptible Power Supply UPS Battery - 50Hz Basic Preventive Maintenance
3512B Petroleum Engines with the ADEM 2 Electronic Control Module E012 High Crankcase Pressure Derate
C27 and C32 Engines for Caterpillar Built Machines Exhaust Sensor Lines - Remove and Install
312F and 313F Excavators Belt - Inspect/Adjust/Replace
3306B Generator Set Safety Messages
3306B Generator Set Generator Bearing Temperature - Measure/Record
3500B Generator Sets Generator Bearing - Lubricate
3306B Generator Set Alternator and Fan Belts - Inspect/Adjust/Replace
3306B Generator Set Generator Bearing - Inspect
Retrofitting for Ultra Lean Burn (ULB) on Certain G3516 Engines{1000, 775E} Retrofitting for Ultra Lean Burn (ULB) on Certain G3516 Engines{1000, 775E}
312F and 313F Excavators Engine Oil Level - Check
C27 and C32 Industrial Engines Exhaust Gas Valve (NRS) - Remove and Install
320E and 323E Excavators Fuel System Primary Filter (Water Separator) Element - Replace
C3.4B Engines Engine Has Early Wear
Replacing the High Pressure Fuel Pump on Certain C7 and C9 Engines{1251, 1714} Replacing the High Pressure Fuel Pump on Certain C7 and C9 Engines{1251, 1714}
312F and 313F Excavators Fumes Disposal Filter Element - Replace
C27 and C32 Engines for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C3.4B Engines Engine Overspeeds
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3516C Locomotive Engines Selective Catalytic Reduction Module - Assemble
XQ Auto Paralleling Engine Stopping