Position the Valve Mechanism Before Maintenance Procedures
Show/hide table
注意 |
---|
拆卸摇臂轴前,确保执行此步骤。 |
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A (1)     | 9U-6198     | 曲轴转动工具     | 1     |
A (2)     | 5P-7306     | 壳体     | 1     |
5P-7305 | 发动机盘车工具     | 1     | |
B     | 8T-5096     | 千分表总成     | 1     |
Show/hide table
( 1 ) | 曲轴转动工具用于前皮带轮。 |
( 2 ) | 该工具在电动起动马达的孔上使用。 |
Show/hide table
图 1 | g01334425 |
气缸和气门的位置 (A) 排气门 (B) 进气门 |
- 拆下气门机构盖。 请参考拆解和组装, "气门机构盖 - 拆卸和安装"以了解正确步骤。
- 卸下电热塞。 请参阅拆解和组装, "电热塞 - 拆卸和安装",以了解正确的程序。
- 选择一个可以接近的排气摇臂。 排气摇臂可以处于任何气缸上。
- 使用工具 (A) 旋转曲轴,直到选定排气门的推杆端达到最大高度。 这表示液压挺杆坐在凸轮轴凸轮的基圆上。
- 安装工具 (B) ,使指针接触到推杆上方排气摇臂 (1) 的顶面。
Show/hide table
图 2 | g02313413 |
典型示例 为清楚起见,图中有一个电子单体喷油器未显示。 |
- 使用工具 (A) 旋转曲轴,直到液压挺杆开始打开排气门。 继续旋转曲轴,直到指示器的指针移动 2.8 mm (0.11 in)。
注: 这是 60 度的安全位置。 视液压挺杆是否回降,精确的位置可能有所不同。 随着液压挺杆继续回降,千分表上的读数可能减少。 达到 2.8 mm (0.11 in) 的值后,曲轴处于安全位置。
注: 发动机处于安全位置后,在减振器和前壳体上做临时标记。
Show/hide table
注意 |
---|
安装摇臂轴组件前,确保曲轴位于安全位置。 |
Caterpillar Information System:
C6.6 Industrial Engine Fuel Injection Pump Gear - Remove
C6.6 Industrial Engine Fuel Injection Pump - Install
Procedure to Install a New Software with Droop Capability for Load Sharing on Certain C11 and C15 Industrial Engines{1901, 1920} Procedure to Install a New Software with Droop Capability for Load Sharing on Certain C11 and C15 Industrial Engines{1901, 1920}
C6.6 Industrial Engine Fuel Injection Pump - Remove
C6.6 Industrial Engine Inlet Air Control - Install - NRS Inlet Air Mixer
C6.6 Industrial Engine Inlet Air Control - Remove - NRS Inlet Air Mixer
C6.6 Industrial Engine Fuel Injection Lines - Install
G3520E Generator Set Engines Air Lines
C6.6 Industrial Engine Fuel Injection Lines - Remove
C6.6 Industrial Engine Fuel Manifold (Rail) - Remove and Install
C6.6 Industrial Engine Fuel Filter Base - Remove and Install - Single Secondary Fuel Filter
C6.6 Industrial Engine Fuel Priming Pump - Remove and Install - Electric Fuel Lift Pump (EFLP)
797F and 797F XQ Off-Highway Trucks Machine Systems Gear Pump (Brake, Rear Axle Lubrication) - Remove and Install
C4.4 Industrial Engine Position the Valve Mechanism Before Maintenance Procedures
3612 and 3616 Fast Vessel Engines Customer Assistance
C18 Marine Engine Sensors and Electrical Components - Engines with 1000 HP or Greater
797F and 797F XQ Off-Highway Trucks Machine Systems Piston Pump (Brake Cooling) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Oil Pump - Remove and Install
797F and 797F XQ Off-Highway Trucks Machine Systems Piston Pump (Hydraulic Fan, Steering) - Remove and Install
C13 Tier 4 Final Engines Soot Antenna
C6.6 Industrial Engine Fuel Injection Pump Gear - Install
G3520E Generator Set Engines Turbocharger Oil Lines
C6.6 Industrial Engine Electronic Unit Injector - Remove
C6.6 Industrial Engine Electronic Unit Injector - Install