Exhaust Manifold
Show/hide table
Illustration 1 | g02671517 |
Show/hide table
Specification for 343-0583 Exhaust Manifold Gp, 343-0584 Exhaust Manifold Gp, and 343-0585 Exhaust Manifold Gp | |||
Item | Qty | Part | Specification Description |
1 | 2 | - | Before assembly, apply a thin coat of 2P-2333 High Temperature Sealer to the outside diameter of the male end of the exhaust manifold. Remove excess high temperature sealer from the assembled joint. |
2 | 2 | 9N-5085 Clamp | Torque the clamp nuts to |
3 | 4 | 245-9750 Taperlock Stud | Torque to |
4 | 6 | 161-3411 Gasket | Install the gaskets for the exhaust manifold with the tabs toward the cylinder block. |
Show/hide table
Illustration 2 | g02671518 |
View A-A |
Show/hide table
Illustration 3 | g02671519 |
Tightening sequence |
Show/hide table
Specification for 343-0583 Exhaust Manifold Gp, 343-0584 Exhaust Manifold Gp, and 343-0585 Exhaust Manifold Gp | |||
Item | Qty | Part | Specification Description |
5 | 12 | 9X-6620 Locknut | Before assembly, lubricate the threads and bearing surfaces of the locknuts with Loctite C5A copper anti-seize. |
Tighten the locknut in the numerical sequence as shown in the Illustration 3 to |
|||
6 | 12 | 116-3715 Taperlock Stud | Torque to |
Caterpillar Information System:
Roller Service Evaluation Checklist {4154, 4180, 4181, 7561} Roller Service Evaluation Checklist {4154, 4180, 4181, 7561}
C27 and C32 Tier 4 Engines Water Pump - Test
C13, C15, and C18 Tier 4 Final Engines Crankshaft
C9.3 Tier 4 Interim Engines Configuration Parameters
349F and 352F Excavators Machine System Cylinders (Boom, Stick and Bucket)
C27 and C32 Generator Set Engines Fuel Transfer Pump
Hydraulic Excavator Roller Disassembly and Assembly Procedures {0729, 0768, 4154, 4180, 4181} Hydraulic Excavator Roller Disassembly and Assembly Procedures {0729, 0768, 4154, 4180, 4181}
C13, C15, and C18 Tier 4 Final Engines Cylinder Block
C13, C15, and C18 Tier 4 Final Engines Cylinder Block
2009/12/24 Normal Wear on the Cylinder Liners of Some C11 and C13 Engines {1201}
G3500 Engines Model View Illustrations
3412E and C30 Marine Engines Maintenance Interval Schedule - Fast Craft
C13, C15, and C18 Tier 4 Final Engines Exhaust Lines (DPF Inlet)
C27 and C32 Engines for Caterpillar Built Machines Exhaust Temperature Is High
C4.4 Industrial Engine High Pressure Fuel Lines
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553} Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
C4.4 Industrial Engine Electrical System
C6.6 Marine Generator Set ECM Memory - Test
C15 and C18 Engines for Caterpillar Built Machines Speed Control - Test
C175-16 PETROLEUM ENGINES Engine Oil and Water Pump Drive - Disassemble
C175-16 PETROLEUM ENGINES Engine Oil and Water Pump Drive - Assemble
C27 and C32 Engines for Caterpillar Built Machines Oil Contains Coolant
C6.6 Generator Set Engine Pressure Sensor Open or Short Circuit - Test
2010/01/28 A New Seal Kit Is Used on G3500C and G3500E Aftercoolers {1063, 7555}