Turbocharger
Show/hide table
| NOTICE |
|---|
|
The correct procedures and tooling specifications must always be used. Failure to follow any of the procedures may result in damage, malfunction, or possible engine failure. |
Show/hide table
| |
| Illustration 1 | g02981861 |
|
Rear view of engine | |
Show/hide table
| |
| Illustration 2 | g02981862 |
|
Right side view of engine | |
Show/hide table
| Specification for 345-8994 Turbocharger Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 4 | 375-2467 Flange Locknut | Use the following procedure in order to mount the turbocharger:
1. Loosen the nuts of compressor clamp assembly and band clamp enough to allow housing to rotate. Excessive loosening of the housings will cause contact. Possible damage to the wheel may occur. 2. Before assembly, lubricate the threads and the bearing surfaces with Loctite C5A Copper Anti-Seize. 3. Mount the gasket (3) over the studs in the exhaust manifold. 4. Mount the turbocharger onto the exhaust manifold. 5. Tighten the flange locknuts to |
| 4 | 1 | 239-5858 Compressor Clamp Assembly | Use the following procedure in order to tighten the compressor clamp and band clamp assembly:
1. Place the bearing housing (8) with the oil supply (6) and the oil drain (9) in the vertical position with respect to the engine as shown in the Illustration 2. 2. Position the compressor clamp (4) so that the threaded rod points downward on the outboard side of the turbocharger as shown in the Illustration 2. 3. Tighten the band clamp (5) on the 385-3580 Turbine Housing As (7) enough to prevent the bearing housing (8) from rotating. 4. Position the air outlet (2) of the compressor at 42 degrees (A) from the vertical (A). Position the air outlet (2) of the compressor on the side that is away from the engine as shown in the Illustration 1. 5. Tighten the compressor clamp (4) enough to prevent the compressor from rotating. 6. Tighten the nuts of both clamps to 7. Gently tap both clamps around the circumference of the clamps. 8. Again, tighten the nuts of both clamps to |
| 5 | 1 | 361-7980 Band Clamp | |
Caterpillar Information System:
Caterpillar On-Highway Diesel Engine Fluids Recommendations Biodiesel
3508C, 3512C, and 3516C Locomotive Engines Overspeed Verify - Test
G3304B and G3306B Engines Cylinder Head - Install
3508C, 3512C, and 3516C Locomotive Engines Injector Solenoid - Test
3500 Engines Thermocouple
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Pilot Lines
2009/08/24 New Fuel Injection Lines {1251, 1252}
3508C, 3512C and 3516C Locomotive Engines Turbocharger Oil Lines
345D, 349D and 349D2 Excavator Machine System Specifications Pilot Lines - Stick Lowering Control
797F and 797F XQ Off-Highway Truck Braking System Solenoid Valve (Rear Axle Motor Unloader)
797F and 797F XQ Off-Highway Truck Braking System Solenoid Valve (Brake Cooling)
Procedure to Apply Dielectric Grease to the Horn (Cruise Control) Contact Ring{4310} Procedure to Apply Dielectric Grease to the Horn (Cruise Control) Contact Ring{4310}
G3304B and G3306B Engines Connecting Rod Bearings - Remove and Install
3508C, 3512C, and 3516C Locomotive Engines Sensor Signal (PWM) - Test
3508C, 3512C, and 3516C Locomotive Engines Sensor Signal (Analog, Active) - Test
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine System Boom - 6.90 m (22.638 ft)
G3304B and G3306B Engines Piston and Connecting Rods - Remove
C13 Engine for Combat and Tactical Vehicles Engine Oil Cooler
G3304B and G3306B Engines Piston and Connecting Rods - Install
G3512E Generator Set Engine Ignition Primary - Test
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1823 - FMI 03
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 1823 - FMI 04
G3304B and G3306B Engines Piston and Connecting Rods - Disassemble
C13 Engine for Combat and Tactical Vehicles Water Temperature Regulator Housing