Pump Drive - Assemble - Integral
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
C     | 8T-5096     | 千分表总成     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 安装挡圈 (15) 。
Show/hide table
图 1 | g01950720 |
- 冷却轴承外圈 (16) 。 安装轴承外圈 (16) 。 安装轴承内圈 (15) 。 在对面重新执行此步骤。
Show/hide table
图 2 | g01950691 |
- 安装惰轮组件 (14) 。
Show/hide table
图 3 | g01950686 |
- 安装惰轮轴 (13) 。 安装螺栓 (12) 和垫圈。 安装 O 型密封圈 (11) 。
Show/hide table
图 4 | g01950685 |
- 安装盖 (10) 。
Show/hide table
图 5 | g01950683 |
- 降低轴承外环 (9) 的温度。 安装轴承外环 (9) 。
Show/hide table
图 6 | g01950681 |
- 加热轴承内圈 (8) 。 安装轴承内圈 (8) 。 对其余轴承内环重新执行此步骤。
Show/hide table
图 7 | g01950781 |
- 安装密封圈 (7) 。
Show/hide table
图 8 | g01950613 |
- 安装泵驱动齿轮 (6) 。
Show/hide table
图 9 | g01950591 |
- 冷却轴承外圈 (5) 。 安装轴承外圈 (5) 。
Show/hide table
图 10 | g01950590 |
- 安装 O 形密封圈 (4) 。
Show/hide table
图 11 | g01950588 |
- 安装垫片 (3) 。 安装泵适配器 (2) 。 安装螺栓 (1) 。 将螺栓拧紧至 55 ± 10 N·m (41 ± 7.4 lb ft)。
Show/hide table
图 12 | g01950783 |
- 使用工具 (C) 测量泵驱动齿轮 (6) 的端隙。 端隙测量值必须为 0.10 至 0.20 mm (0.004 至 0.008 in)。 增加或减少垫片以便达到正确的端隙。
Show/hide table
图 13 | g01950773 |
- 对其余的泵驱动齿轮重复步骤 5 到步骤 13。
End By: 安装泵驱动装置。 请参阅 拆解和组装, "泵驱动装置 - 安装"。
Caterpillar Information System:
CX35-P800-C18I and CX35-P800-C27I Petroleum Power Train Packages and CX35-P800 Petroleum Transmission Event Code List
793F Off-Highway Truck Engine Supplement Air Starting Motor - Remove and Install
C12 Marine Engines Maintenance Recommendations
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install
C13 Industrial Engines Fuel Filter Base - Secondary Fuel Filter
C18 Marine Engines Oil Cooler Core - Check/Clean/Test - If Equipped
C13 Industrial Engines Fuel Filter Base - Secondary Fuel Filter
C9.3 Tier 4 Final Engines Lubrication System
C9.3 Engines for Caterpillar Built Machines Diesel Particulate Filter - Remove and Install - Diesel Oxidation Catalyst, Clean Emissions Module
C13, C15, and C18 Tier 4 Interim Engines ARD Does Not Activate
C9.3 Engines for Caterpillar Built Machines Muffler - Remove and Install
C9.3 Engines for Caterpillar Built Machines Air Cleaner Housing - Remove and Install
CX35-P800 Petroleum Transmission and Petroleum Power Train Packages Pump Drive - Disassemble - Integral
G3304B and G3306B Engines Aftercooler
793F and 797F Off-Highway Trucks Braking System Automatic Retarder - Calibrate
793F and 793F CMD Off-Highway Truck Braking System Pressure Sensor (Brake Pump)
793F and 797F Off-Highway Trucks Braking System Glossary of Electrical Terms
793F and 793F CMD Off-Highway Truck Hydraulic System Hoist Control
C4.4 Industrial Engine Engine Starting
793F and 793F CMD Off-Highway Truck Air System General Information
Camshaft Lobe Hits Fuel Transfer Pump.{1210, 1256} Camshaft Lobe Hits Fuel Transfer Pump.{1210, 1256}
793F and 793F CMD Off-Highway Truck Braking System Brake System
C175 Generator Sets Starting Motor - Inspect - If equipped
C9 Marine Engines Maintenance Recommendations