Fault Identification
Show/hide table
| Fault Identification | ||||
| Indicator left side of GSC+P |
Fault Code on upper display | DIAG Indicator | Fault Type | Refer to Topic |
| Fault Alarm | CID FMI (1) | Flashing | Active Alarm | Troubleshooting Diagnostic Codes |
| SP1, SP2, SP3, SP4 (1) | Absent | Active Alarm | Diagnostic System Procedures, "SP Fault Code" | |
| AL1 thru AL15 (1) | Absent | Active Alarm | Diagnostic System Procedures, "AL Fault Code" | |
| Fault Shutdown | CID FMI | Flashing | Active Shutdown | Troubleshooting Diagnostic Codes |
| SP1, SP2, SP3, SP4 | Absent | Active Shutdown | Diagnostic System Procedures, "SP Fault Code" | |
| AL5 thru AL15 (1) | Absent | Active Alarm | Diagnostic System Procedures, "AL Fault Code" | |
| Dedicated Shutdown: | ||||
| Flashing | Absent | Absent | Active Alarm | Troubleshooting Dedicated Shutdown Indicators |
| On Continuously | Absent | Absent | Active Shutdown | |
| None | CID FMI (2) | On Continuously | Inactive Alarm | Troubleshooting Diagnostic Codes |
| CID FMI (2) | On Continuously | Inactive Shutdown | Troubleshooting Diagnostic Codes | |
| SP1, SP2, SP3, SP4 | Absent | Inactive Shutdown | Diagnostic System Procedures, "SP Fault Code" | |
| AL5 through AL15 (1) | Absent | Inactive Alarm | Diagnostic System Procedures, "AL Fault Code" | |
| Absent | Absent | Undiagnosed Shutdown | Symptom Procedures | |
Show/hide table
| ( 1 ) | Fault code is shown after alarm codes key is pressed. |
| ( 2 ) | Fault Code is stored in the fault log of the GSC+P. To view the fault code, see Systems Operation, "Fault Log Viewing OP1" within the topic Service Mode. |
Show/hide table
 | |
| Illustration 1 | g00614724 |
GSC+P Display Area (1) Dedicated shutdown indicators (2) Spare fault indicators (3) Fault shutdown indicator (4) Fault alarm indicator (5) Upper display (6) Lower display (7) Keypad (8) DIAG indicator | |
Faults that are detected and diagnosed by the GSC+P are shown to service personnel in the display area of the GSC+P. The GSC+P uses dedicated shutdown indicators (1), fault shutdown indicator (3), fault alarm indicator (4), "DIAG" indicator (8), upper display (5) and lower display (6) to tell service personnel about a fault. Perform the following procedure in order to identify the fault that is detected by the GSC+P.
Note: The "DIAG" indicator (8) functions when diagnostic information is available from the GSC+P.
- Make a note of the indicators that are functioning on the left side of the "GSC+P".
- View the fault code on the upper display (5). If the fault alarm indicator (4) is FLASHING and no fault code is present on the upper display (5), press the alarm codes key in order to view the fault code.
- Make a note of whether or not "DIAG" indicator (8) is FLASHING ON CONTINUOUSLY or ABSENT.
- On the fault identification chart, look at the first column. Locate the fault indicator that is functioning.
- Go to the second column in the chart. Find the fault code that is presently shown on the upper display (5) .
- Go to the third column in the chart which describes the status of "DIAG" indicator (8) .
- Read the last two columns in order to find the type of fault and corresponding topic within this module.
Caterpillar Information System:
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Service Tools
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) General Information
C175-16 and C175-20 Generator Set Engines Coolant Pressure Is Low
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Indicator for Low Coolant Level
G3500 Generator Sets Configuration Parameters
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Oil Pressure Is Low
An Operation and Maintenance Manual Is Now Available for C7, C9, C13, and C15 On-highway Truck Engines with a 2007 Model Year Regarding the Idle Shutdown Mode{1000, 7938} An Operation and Maintenance Manual Is Now Available for C7, C9, C13, and C15 On-highway Truck Engines with a 2007 Model Year Regarding the Idle Shutdown Mode{1000, 7938}
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Oil Filter Differential Pressure Problem
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Inlet Air Is Restricted
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module High Altitude Derate Occurrence
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Fuel Pressure Is Low
C9 Petroleum Engines Aftercooler - Remove
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0100 - FMI 02
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0110 - FMI 02
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) GSC CID 0248 - FMI 09
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module Engine Control Switch - Test
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) General Information
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) EMCP Electronic Control (Generator Set)
C15 Petroleum Generator Set Engines Camshaft
Installation of the Heated Nozzle for the Caterpillar Regeneration System (CRS){107P, 108B, 1408, 1743, 1803, 1901, 7620} Installation of the Heated Nozzle for the Caterpillar Regeneration System (CRS){107P, 108B, 1408, 1743, 1803, 1901, 7620}
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Instrument Panel
Electronic Modular Control Panel II+ Paralleling (EMCP II+P) Data Link
Troubleshooting Acceleration Issues on Caterpillar On-highway Truck Engines That Are Equipped with Automatic Transmissions {1000, 3030} Troubleshooting Acceleration Issues on Caterpillar On-highway Truck Engines That Are Equipped with Automatic Transmissions {1000, 3030}
14L Motor Grader Machine Systems Wheel Mounting - AWD