Fuel Lines - Fuel Lines for the High Pressure Fuel Pump
Show/hide table
| |
| 图 1 | g03082965 |
|
(1) 341-6784 燃油管
(2) 341-6785 燃油管 (3) 360-1596 块 (4) 311-8193 螺栓 (5) 328-7116 支架组件 (6) 327-7734 燃油油轨总成 (7) 6V-5815 螺栓 (8) 6V-5839 垫圈 | |
Show/hide table
| 304-9602 喷油管总成的技术规格 |
| 注：执行下述步骤，以安装高压燃油管。 注：安装前，使用清洁的发动机机油润滑燃油管两端。 1. 将燃油管 (2) 插入燃油油轨 (6) 和块 (3)。 使用螺栓 (4) 和垫圈 (8) 将燃油管 (2) 固定到燃油油轨 (6) 和块 (3) 上。 2. 将螺栓 (4) 均匀手动拧紧到燃油油轨 (6) 上。 3. 使用螺栓 (7) 将块 (3) 均匀手动拧紧到燃油泵适配器（未显示）上。 4. 将螺栓 (4) 均匀拧紧到燃油油轨 (6) 上，扭矩为 5. 将螺栓 (4) 均匀拧紧到块 (3) 上，扭矩为 6. 将螺栓 (7) 均匀拧紧到泵适配器上，扭矩为 7. 将螺栓 (4) 均匀拧紧到燃油油轨 (6) 上，扭矩为 8. 将螺栓 (4) 均匀拧紧到块 (3) 上，扭矩为 9. 按标准扭矩将螺栓 (7) 均匀拧紧到泵适配器上。 10. 安装支架 (5) 和所有安装固件。 11. 将燃油管 (1) 插入高压燃油泵和块 (3)。 使用螺栓 (4) 和垫圈 (8) 将燃油管 (1) 连接到高压燃油泵和块 (3) 上。 12. 将螺栓 (4) 均匀手动拧紧到高压燃油泵上。 13. 将螺栓 (4) 均匀手动拧紧到块 (3) 上。 14. 将螺栓 (4) 均匀拧紧到高压燃油泵上，扭矩为 15. 将螺栓 (4) 均匀拧紧到块 (3) 上，扭矩为 16. 将螺栓 (4) 均匀拧紧到高压燃油泵上，扭矩为 17. 将螺栓 (4) 均匀拧紧到块 (3) 上，扭矩为 18. 安装支架 (5) 和所有安装固件。 |
Caterpillar Information System:
2007/10/29 Improved Securing of the Wiring Harness {1408}
C15 and C18 Petrolem Generator Set Engines Component Location
C15 and C18 Petrolem Generator Set Engines Configuration Parameters
G3520B Engine Sensors and Electrical Components
C9 Petroleum Engines Turbocharger
G3520B Industrial Engines Sensor Signal (Analog, Passive) - Test
C15 and C18 Petrolem Generator Set Engines Diagnostic Trouble Codes
G3520B Engine Specifications
G3520B Engine Product Description
3608 Engine Piston and Connecting Rods - Install
3608 Engine Piston and Connecting Rods - Remove
C3.3 Industrial Engine Engine Design
C27 and C32 Tier 4 Engines Flywheel Housing
C27 and C32 Industrial and Petroleum Engines Flywheel Housing
C27 and C32 Industrial and Petroleum Engines Flywheel Housing
G3520B Engine Refill Capacities and Recommendations
2007/10/08 Improved Exhaust Riser Brackets are Now Available {1059, 1154}
2007/10/22 A New Spring Helps to Relieve Combustion Pressure {1550}
Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 9, 10, and 11) {5061, 506G, 5073} Specifications and Reusability for Hydraulic Gear Pumps and Motors (Groups 9, 10, and 11) {5061, 506G, 5073}
2007/10/01 Improvements for the Engine Oil Cooler Are Now Used {1378, 1380}
2007/10/08 Improvements for the Engine Oil Cooler Are Now Used {1378}
2007/10/01 Improvements for the Engine Oil Cooler Are Now Used {1378}
C15 and C18 Petrolem Generator Set Engines Oil Temperature Is High
3608 Engine Crankshaft Front Seal - Install