Engine Stalls at Low RPM
- Diagnostic codes
- Accessory equipment
- Power mode control (if equipped)
- Fuel supply
- Low compression (cylinder pressure)
- Electronic unit injectors
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Diagnostic Codes A. Establish communication between the electronic service tool and the Electronic Control Module (ECM) . If necessary, refer to Troubleshooting, "Electronic Service Tools". B. Check if any codes are active or logged. |
Diagnostic code |
Result: A code is active or logged. Repair: Troubleshoot any codes before continuing with this procedure. Result: A code is not active or logged. Proceed to Test Step 2. |
2. Accessory Equipment A. Check all accessory equipment for faults that may create excessive load on the engine. |
Accessories |
Result: An engine accessory is creating an excessive load. Repair: Repair or replace the engine accessory. Result: An engine accessory is not creating an excessive load. Proceed to Test Step 3. |
3. Power Mode Control (If Equipped) A. Check whether the power mode control is using the Cat data link or the CAN data link and then use the appropriate test. Refer to Troubleshooting, "Data Link - Test" or Troubleshooting, "CAN Data Link - Test". B. Check the engine wiring harness for defects. Refer to Troubleshooting, "Electrical Connectors - Inspect". |
Power mode control |
Result: There is a fault in the data link. Repair: Repair the data link, as necessary. Result: There is a wiring fault. Repair: Repair or replace the wiring, as necessary. Result: The data link and the wiring are OK. Proceed to Test Step 4. |
4. Fuel Supply A. Ensure that the vent in the fuel cap is not filled with debris. B. Ensure that the fuel supply valve (if equipped) is in the full OPEN position. C. If the temperature is below D. Check the primary filter/water separator for water in the fuel. E. Check for fuel supply lines that are restricted. F. Replace the in-line fuel filter that is installed upstream of the Electric Fuel Lift Pump (EFLP). G. Check that the EFLP is operating correctly. H. Replace the primary and secondary fuel filters. I. Check the diesel fuel for contamination. Refer to Systems Operation, Testing, and Adjusting, "Fuel Quality - Test". J. Check for air in the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Air in Fuel - Test". |
Fuel system |
Result: The vent in the fuel cap is blocked. Repair: Install a replacement fuel cap. Result: The fuel contains solidified wax. Repair: Replace the fuel with fuel of the correct specification for the ambient conditions. Result: There are fuel supply lines that are restricted. Repair: Replace any damaged or restricted fuel lines. The EFLP is suspect. Refer to Troubleshooting, "Fuel Pump Relay Circuit - Test". Replace the primary fuel filter and the secondary fuel filters. Refer to the Operation and Maintenance Manual for further information. Result: There is air in the fuel system. Repair: Prime the fuel system. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime". Result: The diesel fuel is contaminated. Repair: Drain the fuel tank and the fuel system. Replace the primary fuel filter and the secondary fuel filters. Refer to the Operation and Maintenance Manual for further information. Fill and prime the fuel system with fuel of the correct specification. Refer to Systems Operation, Testing, and Adjusting, "Fuel System - Prime". Result: The fuel supply is OK. Proceed to Test Step 5. |
5. Low Compression (Cylinder Pressure) A. Perform a compression test. Refer to Systems Operation, Testing, and Adjusting, "Compression - Test". |
Cylinder compression |
Result: The results of the compression test are outside the specifications. Repair: Investigate the cause and rectify any faults. Note: Possible causes of low compression are shown in the following list: · Loose glow plugs · Faulty piston · Faulty piston rings · Worn cylinder bores · Worn valves · Faulty cylinder head gasket · Damaged cylinder head Result: The results of the compression test are OK. Proceed to Test Step 6. |
Show/hide table
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death. |
Show/hide table
NOTICE |
---|
Contact with high-pressure fuel may cause personal injury or death. Wait 10 minutes after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines. |
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
6. Electronic Unit Injectors A. Use the electronic service tool to perform the automatic "Cylinder Cut Out Test". Note: If the compression test that was performed in Test Step 5 was satisfactory, the "Cylinder Cut Out Test" will identify any faulty injectors. |
Electronic Unit Injectors |
Result: A faulty injector is indicated. Repair: Remove any faulty electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove". Install new electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install". Repeat the automatic "Cylinder Cut Out Test". If the fault is still apparent, remove the replacement electronic unit injector and install the original electronic unit injector. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove" and Disassembly and Assembly, "Electronic Unit Injector - Install". Result: All injectors are OK. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
C7.1 Engines and Generator Sets Engine Shutdown Occurs Intermittently
980L Tier 3 Wheel Loader Machine System Piston Pump (Brake, Pilot, Fan) - Assemble
C7.1 Engines and Generator Sets Engine Shutdown Occurrence
992K Wheel Loader Systems Gear Pump - Secondary Steering
980L Tier 3 Wheel Loader Engine Supplement Aftercooler - Remove and Install
980L Tier 3 Wheel Loader Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove and Install
C7.1 Engines and Generator Sets Engine Overspeeds
C7.1 Engines and Generator Sets Engine Misfires, Runs Rough or Is Unstable
C7.1 Engines and Generator Sets Engine Has Mechanical Noise (Knock)
C7.1 Engines and Generator Sets Engine Has Early Wear
C7.1 Engines and Generator Sets Engine Does Not Crank
980L Tier 3 Wheel Loader Engine Supplement Radiator Core - Remove and Install
C7.1 Engines and Generator Sets Engine Top Speed Is Not Obtained
C7.1 Engines and Generator Sets Engine Vibration Is Excessive
C7.1 Engines and Generator Sets Exhaust Has Excessive Black Smoke
980L Tier 3 Wheel Loader Machine System Piston Pump (Brake, Pilot, Fan) - Disassemble
C7.1 Engines and Generator Sets Exhaust Has Excessive White Smoke
An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324} An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324}
950 GC Wheel Loader Power Train Transmission Oil Pump
926M, 930M and 938M Wheel Loaders Cooling System Coolant Extender (ELC) - Add
950 GC Wheel Loader Power Train Transmission Oil Cooler
MD6310 Rotary Drill Air Compressor Oil - Change
MD6310 Rotary Drill Air Compressor Oil Filter - Change
A New Valve Mechanism Cover and Elbows Are Now Used on Certain 3412, C27, and C32 Machine Engines {1107} A New Valve Mechanism Cover and Elbows Are Now Used on Certain 3412, C27, and C32 Machine Engines {1107}