Engine Shutdown Occurs Intermittently
Note: Use this procedure only if the engine shuts down completely during operation.
- Active codes and logged codes
- Electrical connections
- Unstable fuel supply
- Switches
- Circuit protection
- Engine speed/timing
Show/hide table
Associated Diagnostic Trouble Codes | |
J1939 Code | CDL Code |
3719-0 | E995 (3) |
3719-16 | E995 (2) |
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Active Codes and Logged Codes A. Certain diagnostic codes and/or event codes may cause an engine shutdown. Connect the electronic service tool and check for active codes and for logged codes. B. Use the electronic service tool to check for associated diagnostic trouble codes. Refer to Table 1 |
Codes |
Result: There are associated diagnostic trouble codes active or logged. Repair: Troubleshoot any active or logged associated diagnostic trouble codes before continuing with this procedure. Result: There are no associated diagnostic trouble codes active or logged. Proceed to Test Step 2. |
2. Electrical Connections A. Check for the correct installation of the ECM J1/P1 and the J2/P2 connectors. Check for correct installation of the fuel injector connectors. |
Connectors |
Result: There are suspect connectors. Repair: Perform the "Wiggle Test" on the electronic service tool. Repair or replace connectors that are suspect. Result: There are no suspect connectors. Proceed to Test Step 3. |
3. Electrical Connections A. Check the power and ground connections to the ECM. Refer to Troubleshooting, "Electrical Power Supply - Test". |
Electrical Connectors |
Result: The electrical connections are OK. Proceed to Test Step 4. Result: The electrical connections are not OK. Repair: Repair or replace the damaged connectors. Verify that the repair eliminated the fault. |
4. Unstable Fuel Supply A. Inspect the fuel system. Refer to Systems Operation/Testing and Adjusting, "Fuel System - Inspect" for additional information. Cold weather adversely affects the characteristics of the fuel. Refer to the engine Operation and Maintenance Manual, "Cold Weather Operation" for further information. B. Check fuel quality. Check the fuel tank for debris or foreign objects which may block the fuel supply. |
Fuel |
Result: The fuel quality is OK. Proceed to Test Step 5. Result: The fuel quality is not OK. Repair: Replace the fuel. Verify that the repair eliminated the fault. |
5. Switches A. Check the keyswitch input to the ECM. B. Check any engine shutdown switches and associated wiring. |
Switches |
Result: The shutdown switches and wiring are OK. Proceed to Test Step 6. Result: The shutdown switches and wiring are not OK. Repair: Make the necessary repairs, Verify that the repair eliminated the fault. |
6. Circuit Protection A. Inspect the wires and connectors to all circuit protection for the engine. B. Check the device for circuit protection. |
Circuit protection |
Result A circuit protection device is tripped. Repair: Reset the circuit breaker if a circuit breaker is tripped. If necessary, replace blown fuses. Prior to returning the engine to service, determine the condition that caused the circuit breaker to trip or the fuse to blow. Make the necessary repairs. Result The circuit protection is OK. Proceed to Test Step 7. |
8. Engine Speed/Timing Sensors A. Inspect the connectors for the engine speed/timing sensors. B. Crank the engine. If the engine starts and no speed timing codes are logged, the speed timing circuit is operating correctly. |
Speed/Timing |
Result: The Speed/Timing sensor circuit is not operating correctly. Repair: Test the speed/timing circuit. Refer to Troubleshooting, "Speed/Timing `- Test". Verify that the repair eliminated the fault. If the fault is still present, contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
980L Tier 3 Wheel Loader Machine System Piston Pump (Brake, Pilot, Fan) - Assemble
C7.1 Engines and Generator Sets Engine Shutdown Occurrence
992K Wheel Loader Systems Gear Pump - Secondary Steering
980L Tier 3 Wheel Loader Engine Supplement Aftercooler - Remove and Install
980L Tier 3 Wheel Loader Engine Supplement Fan Group (Includes Fan, Fan Guard, Fan Shroud, and Hydraulic Fan Motor) - Remove and Install
C7.1 Engines and Generator Sets Engine Overspeeds
C7.1 Engines and Generator Sets Engine Misfires, Runs Rough or Is Unstable
C7.1 Engines and Generator Sets Engine Has Mechanical Noise (Knock)
C7.1 Engines and Generator Sets Engine Has Early Wear
C7.1 Engines and Generator Sets Engine Does Not Crank
980L Tier 3 Wheel Loader Engine Supplement Radiator Core - Remove and Install
C7.1 Engines and Generator Sets Engine Cranks but Does Not Start
C7.1 Engines and Generator Sets Engine Stalls at Low RPM
C7.1 Engines and Generator Sets Engine Top Speed Is Not Obtained
C7.1 Engines and Generator Sets Engine Vibration Is Excessive
C7.1 Engines and Generator Sets Exhaust Has Excessive Black Smoke
980L Tier 3 Wheel Loader Machine System Piston Pump (Brake, Pilot, Fan) - Disassemble
C7.1 Engines and Generator Sets Exhaust Has Excessive White Smoke
An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324} An Installation Procedure for the TLV2 Seat Suspension Harness is Now Available {1408, 7324}
950 GC Wheel Loader Power Train Transmission Oil Pump
926M, 930M and 938M Wheel Loaders Cooling System Coolant Extender (ELC) - Add
950 GC Wheel Loader Power Train Transmission Oil Cooler
MD6310 Rotary Drill Air Compressor Oil - Change
MD6310 Rotary Drill Air Compressor Oil Filter - Change