C15 and C18 Industrial Engines Caterpillar


Engine Top Speed Is Not Obtained

Usage:

C18 EJG
Note: If this problem occurs only under load, refer to Troubleshooting, "Power Is Intermittently Low or Power Cutout Is Intermittent".

Probable Causes

  • Diagnostic codes and events

  • Starting aids

  • Active engine derate

  • Decelerator pedal position sensor

  • Throttle position sensor

  • Intake manifold pressure sensor and atmospheric pressure sensor

  • Fuel supply

  • Air inlet and exhaust system

  • Accessory equipment

Recommended Actions

Diagnostic Codes and Events

Use Caterpillar Electronic Technician (ET) to check for logged derates. The engine speed or the engine power may be limited due to one of the following conditions: high altitude, high intake manifold air temperature, low oil pressure, air filter restriction and other factors. Refer to Troubleshooting, "Event Codes List" for the specific events that are applicable to this application.

Starting Aids

Ether Injection System (If Equipped)

Check the operation of the ether injection system. Ensure that the ether injection system is operating properly. For additional information on troubleshooting electrical problems with the ether injection system, refer to ON position. For additional information, refer to Troubleshooting, "Ether Starting Aid - Test" or refer to Troubleshooting, "Starting Aid - Test" for details.

Decelerator Pedal Position Sensor

Monitor the decelerator pedal on Cat ET. Verify that the decelerator pedal is operating properly. Refer to Troubleshooting, "Speed Control - Test" for the proper troubleshooting procedures.

Throttle Position Sensor

Monitor the switch signal on Cat ET. Verify that the signal is stable at the low idle position. Verify that the signal is stable at the high idle position. Move the switch from the low idle position to the high idle position in order to verify that the engine is able to reach the high idle position. Refer to Troubleshooting, "Speed Control - Test" for the proper troubleshooting procedure.

Intake Manifold Pressure Sensor and Atmospheric Pressure Sensor

  1. Monitor the status of "Fuel Position", of "Rated Fuel Limit", and of "FRC Fuel Limit" on Cat ET while the engine is operating under full load. These parameters must reflect the information below.

    Table 1
    "Fuel Position" = "Rated Fuel Limit"
    and
    "Fuel Position" < "FRC Fuel Limit"    

    If "Fuel Position" equals "Rated Fuel Limit" and "Fuel Position" is less than "FRC Fuel Limit", the electronics are operating correctly. Otherwise, proceed with the next Step.

  1. Use Cat ET in order to monitor the status of the "Boost Pressure". With the engine stopped, the correct "Boost Pressure" is 0 kPa (0 psi).

  1. Start the engine and monitor the status of "Boost Pressure" while you vary the engine speed. Ensure that the pressure reading is fluctuating with the engine speed.

  1. Use Cat ET in order to check the status of the "Atmospheric Pressure". Verify that the pressure reading is reasonable for the current conditions.

Fuel Supply

  1. Check the fuel lines for the following problems: restrictions, collapsed lines and pinched lines. If problems are found with the fuel lines, repair the lines and/or replace the lines.

  1. Check the fuel tank for foreign objects or debris which may block the fuel supply.

  1. Prime the fuel system if any of the following items have been serviced recently:

    • Fuel filters

    • Low pressure fuel supply circuit

    • Unit injectors

    Note: A sight glass in the low pressure supply line is helpful in diagnosing air in the fuel. Refer to Systems Operation/Testing and Adjusting, "Air in Fuel - Test" for more information.


    NOTICE

    Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.


  1. Cold weather adversely affects the characteristics of the fuel. Refer to the Operation and Maintenance Manual for information on improving the characteristics of the fuel during cold weather operation.

  1. Check the fuel pressure during engine cranking. Refer to Systems Operation/Testing and Adjusting, "Fuel System" for the correct procedure. If the fuel pressure is below specifications, replace the fuel filters. If this does not correct the problem, check for the proper operation of the following items: fuel transfer pump, fuel pressure relief valve and fuel pressure regulator valve.

Air Inlet and Exhaust System

  1. Check for an air filter restriction indicator. Clean plugged air filters or replace plugged air filters. Refer to the Operation and Maintenance Manual.

  1. Check the air inlet and exhaust system for restrictions and/or leaks. Refer to Systems Operation/Testing and Adjusting, "Air Inlet and Exhaust System".

Accessory Equipment

Check all accessory equipment for problems that may create excessive load on the engine. Make the necessary repairs to damaged components. Replace parts, if necessary.

Caterpillar Information System:

Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.