Alternator - Remove - Engines Without an Automatic Belt Tensioner
拆卸步骤
开始:
- 拆下 V 形皮带。 请参阅拆解和组装, "V 形皮带 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将断路开关转到断开位置。
- 在线束组件的连接上做出临时的识别标记。
- 将线束组件从交流发电机 (1) 上断开。
Show/hide table
图 1 | g01255718 |
典型示例 |
- 从交流发电机 (4) 上拆下螺栓 (6) 。
- 卸下螺母 (1) 和垫圈 (2) 。 从交流发电机 (4) 上拆下螺栓 (5) 。 从交流发电机支架 (3) 上拆下交流发电机 (4) 。
- 如有必要,从交流发电机 (4) 上拆下皮带轮 (8) 。 遵循步骤 6.a 和 6.b 的方法,从交流发电机上卸下皮带轮。
注: 这种方法不适用于一些皮带轮配置类型。
- 使用六角板手固定交流发电机 (4) 的轴。 使用带曲柄的梅花扳手(套筒扳手)拧松螺母 (7) 。
- 从交流发电机 (4) 上拆下螺母 (7) 和皮带轮 (8) 。
Caterpillar Information System:
C4.4 (MECH) Industrial Engine and Generator Sets Fan Drive - Remove and Install
3512C Industrial Engine Fuel Priming Pump - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fan - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets V-Belts - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Glow Plugs - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft Gear - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Install - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Assemble
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Electric Starting Motor - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Air Compressor - Remove and Install
C7 and C9 On-Highway Engines ARD Fuel Pressure - Test
C7 and C9 On-Highway Engines ARD Ignition - Test
C7 and C9 On-Highway Engines Clean Gas Induction - Test
3512C Engine Sensor Signal (Analog, Passive) - Test
Procedure to Inspect Machines Potentially Damaged Due to Water Submersion{1000, 7000} Procedure to Inspect Machines Potentially Damaged Due to Water Submersion{1000, 7000}
3512C Engine Sensor Signal (PWM) - Test
C15 and C18 Industrial Engines Cat Data Link - Test