Crankshaft Gear - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 8H-0663     | 轴承拉拔器     | 1     |
5F-7345 | 拉拔器     | 1     | |
126-7183 | 十字挡块     | 1     | |
126-7177 | 拉拔器腿     | 2     |
开始:
- 拆卸前壳体。 请参阅拆解和组装, "壳体(前) - 拆卸"。
- 如果发动机配备平衡器,则卸下该平衡器。 请参阅拆解和组装, "平衡器 - 拆卸"。 如果发动机未配备平衡器,则卸下发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 曲轴齿轮在曲轴上可以采用滑动配合,也可以采用干涉配合。
- 如果曲轴齿轮在曲轴上采用滑动配合,将曲轴齿轮 (1) 从曲轴 (2) 上卸下。
如果曲轴齿轮在曲轴上采用干涉配合,使用工具 (A) 将曲轴齿轮 (1) 从曲轴 (2) 上卸下。
Show/hide table
图 1 | g01367358 |
典型示例 |
Show/hide table
图 2 | g01270549 |
典型示例 |
- 如有必要,将键 (3) 从曲轴 (2) 上卸下。
注: 除非键损坏,否则不要从曲轴上卸下键。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 如有必要,将新的键 (3) 安装到曲轴 (2) 上。
Show/hide table
图 3 | g01367359 |
典型示例 |
- 如果曲轴齿轮在曲轴上采用滑动配合,将曲轴齿轮 (1) 中的锁孔与曲轴中的钥匙 (3) 对齐。 将曲轴齿轮 (1) 安装到曲轴 (2) 上。
如果曲轴齿轮在曲轴上采用干涉配合,在烤箱中加热曲轴齿轮 (1) 至 150° ± 50°C (302° ± 90°F)。 将曲轴齿轮 (1) 中的锁孔与曲轴中的钥匙 (3) 对齐。 将曲轴齿轮 (1) 安装到曲轴 (2) 上。
确保曲轴齿轮 (1) 上的凸肩 (4) 朝向发动机前部。
注: 曲轴齿轮在曲轴上可以采用滑动配合,也可以采用干涉配合。
Show/hide table
灼热的零件或部件会烫伤人体。 别让灼热的零件或部件触及您的皮肤。 为了保护您的皮肤,必须穿上保护衣或使用保护装备。 |
End By:
- 安装前壳体。 请参阅 拆解和装配手册, "壳体(前)- 安装"。
- 如果发动机配备平衡器,则安装该平衡器。 请参阅 拆解和组装, "平衡器 - 安装"。 如果发动机未配备平衡器,则安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Install - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Assemble
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Disassemble
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Install
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Piston Cooling Jets - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Balancer - Install
C4.4 (MECH) Industrial Engine and Generator Sets Balancer - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Glow Plugs - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets V-Belts - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Fan - Remove and Install
3512C Industrial Engine Fuel Priming Pump - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fan Drive - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Electric Starting Motor - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Air Compressor - Remove and Install
C7 and C9 On-Highway Engines ARD Fuel Pressure - Test