Fan Drive - Remove and Install
拆卸步骤
开始:
- 拆下风扇。 请参阅拆解和组装, "风扇 - 拆卸和安装"。
- 将螺栓 (1) 从风扇驱动 (2) 上卸下。
注: 确定风扇驱动的朝向和位置。
Show/hide table
图 1 | g01390998 |
典型示例 |
- 拆卸风扇驱动 (2) 。
安装步骤
- 检查风扇驱动有无磨损或损坏。 风扇驱动是一个不可维修的部件。 如果风扇驱动磨损或损坏,更换风扇驱动。
Show/hide table
图 2 | g01390998 |
典型示例 |
- 安装风扇驱动 (2) 。
注: 确保风扇驱动的方向正确。
- 安装螺栓 (1) 。 将螺栓拧紧至扭矩 44 N·m (32 lb ft)。
End By: 安装风扇。 请参阅 拆解和组装, "风扇 - 拆卸和安装"。
Caterpillar Information System:
3512C Industrial Engine Fuel Priming Pump - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fan - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets V-Belts - Remove and Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Glow Plugs - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft Gear - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Install
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Install - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Connecting Rod Bearings - Remove - Connecting rods in position
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Assemble
C4.4 (MECH) Industrial Engine and Generator Sets Pistons and Connecting Rods - Disassemble
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Remove - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines Without an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Remove - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Alternator - Install - Engines With an Automatic Belt Tensioner
C4.4 (MECH) Industrial Engine and Generator Sets Electric Starting Motor - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Air Compressor - Remove and Install
C7 and C9 On-Highway Engines ARD Fuel Pressure - Test
C7 and C9 On-Highway Engines ARD Ignition - Test
C7 and C9 On-Highway Engines Clean Gas Induction - Test
3512C Engine Sensor Signal (Analog, Passive) - Test
Procedure to Inspect Machines Potentially Damaged Due to Water Submersion{1000, 7000} Procedure to Inspect Machines Potentially Damaged Due to Water Submersion{1000, 7000}
3512C Engine Sensor Signal (PWM) - Test