Fuel Priming Pump and Fuel Filter Base - Remove and Install
拆卸步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
注: 为便于安装,在所有软管、所有软管组件、所有导线及所有管组件上作出识别标记。 塞住所有软管组件和管组件。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将燃油供应转到断开位置。
Show/hide table
图 1 | g01318612 |
典型示例 |
- 将蓄电池断路开关转到断开位置。
- 从注油泵 (3) 上断开塑料管组件 (4) 和 (5) 。
- 从注油泵 (3) 上断开塑料管组件 (4) 和 (5) 。
- 从注油泵 (3) 上断开塑料管组件 (2) 。
- 塞住注油泵 (3) 及塑料管组件 (4) 和 (5) 上的所有接头。
- 从注油泵 (3) 上断开线束组件。
- 支承住注油泵。 卸下螺栓和垫圈 (1) ,然后卸下注油泵 (3) 。
注: 记录管组件支架的位置和方向。
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 2 | g01318612 |
典型示例 |
- 确保燃油注油泵清洁、无磨损或损坏。 如有必要,作为一整个组件更换注油泵。
- 将注油泵 (3) 定位到缸盖上。 安装螺栓和垫圈 (1) 。 确保所有螺栓固定的支架安装位置正确。 拧紧螺栓至扭矩为 9 N·m (80 lb in)。
- 从注油泵和塑料管组件上卸下所有塞。 将塑料管组件 (4) 和 (5) 连接到注油泵 (3) 上。
- 将塑料管组件 (2) 连接到注油泵 (3) 上。
- 将线束组件安装到注油泵 (3) 上。
- 将燃油供应转到接通位置。
- 将蓄电池断路开关转到接通位置。
- 排出燃油系统中的空气。 请参阅操作和保养手册, "燃油系统 - 充油"。
Caterpillar Information System:
3512C Engine Injector Solenoid - Test
3512C Engine Plate Locations and Film Locations
2007/08/27 A New Temperature Gauge is Used {7450}
C7 and C9 Petroleum Engines Speed Control (Switch) - Test
C15 and C18 Industrial Engines Electrical Power Supply - Test
C7 Marine Engine Fuel Filter Base
C7 and C9 On-highway Engines Compression Brake - Caterpillar Compression Brake (if equipped)
C15 and C18 Industrial Engines Sensor Signal (Analog, Passive) - Test
C7 and C9 Petroleum Engines Sensor Signal (Analog, Active) - Test
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
C6.6 Industrial Engine Belt Tensioner - Inspect
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Lines - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector Cover - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Install
3512C Industrial Engine Electric Starting Motor - Remove and Install
C7 and C9 Petroleum Engines Sensor Signal (Analog, Passive) - Test
C32 Marine Propulsion Engines Exhaust Temperature Is High
3512C Engine Oil Renewal - Test
3512C Engine Prelubrication - Test
3512C Engine Protection Override - Test