A New Temperature Gauge is Used {7450}
- Engine:
- 3406E (S/N: 6TS1-UP)
- Generator Set:
- 3406 (S/N: 2WB1-UP; 4ZR1-UP)
- Industrial Engine:
- 3406C (S/N: 3ER1-UP)
- Marine Engine:
- 3406C (S/N: 4TB1-UP; 1SS1-UP)
- 3408C (S/N: 1TS1-UP)
- 3412 (S/N: BCS1-UP)
- 3412C (S/N: BAK1-UP; 8AR1-UP; 9BR1-UP)
- 3412E (S/N: 4CR1-UP)
- G3412 (S/N: 3NK1-UP)
- 3406C (S/N: 1LS1-UP)
- 3408B (S/N: 78Z1-UP)
- 3412C (S/N: BAX1-UP; 81Z1-UP)
- 3408B (S/N: 67U1-UP)
- 3412C (S/N: 38S1-UP)
- 3412D (S/N: REA1-UP)
- 3412E (S/N: BDT1-UP)
- 3406E (S/N: 9WR1-UP)
- 3408B (S/N: 99U1-UP)
Show/hide table
Illustration 1 | g01386689 |
The 1W-0700 Temperature Indicator has been cancelled and replaced with the 200-5233 Temperature Indicator. The new gauge has the same chart for the calibration point as well as temperature range. The new gauge is more durable.
The 200-5233 Temperature Indicator has a capillary tube that is 600 mm (23.6 inch) longer than the original 1W-0700 Temperature Indicator. Wind the excess capillary tube into a coil behind the panel. Tie straps must be used in order to secure the longer capillary tube. Install the tie straps in locations (1). Refer to Illustration 2.
Show/hide table
Illustration 2 | g01391643 |
(1) Locations for tie straps (2) Panel |
Show/hide table
Illustration 3 | g01386702 |
Calibration points for the 200-5233 Temperature Indicator |
Show/hide table
Calibration Points for the 200-5233 Temperature Indicator     | |
Point     | Temperature     |
A     | 60 °C (140 °F)     |
B     | 107 to 109 °C (224 to 228 °F)     |
C     | 125 °C (257 °F)     |
Serial number effectivity is listed in Table 2.
Show/hide table
Effectivity for the 200-5233 Temperature Indicator     | |
Engine     | |
3406E     | S/N:6TS27812     |
3408C     | S/N:1TS03316     |
3412     | S/N:BCS02135     |
3412C     | S/N:BAK02241     |
S/N:8AR03454 | |
S/N:9BR03392 | |
3412E     | S/N:4CR04741     |
G3412     | S/N:3NK00155     |
Generator Set     | |
3406     | S/N:2WB18383     |
S/N:4ZR08574 | |
3406C     | S/N:1LS91839     |
3408B     | S/N:78Z08181     |
3412C     | S/N:BAX00247     |
S/N:81Z27799 | |
Industrial Engine     | |
3406C     | S/N:3ER10297     |
3408B     | S/N:67U21930     |
3412C     | S/N:38S24881     |
3412D     | S/N:REU02606     |
3412E     | S/N:BTD05703     |
Marine Engine     | |
3406C     | S/N:4TB09736     |
3406E     | S/N:9WR10479     |
3408B     | S/N:99U12595     |
Caterpillar Information System:
C7 and C9 Petroleum Engines Speed Control (Switch) - Test
C15 and C18 Industrial Engines Electrical Power Supply - Test
C7 Marine Engine Fuel Filter Base
C7 and C9 On-highway Engines Compression Brake - Caterpillar Compression Brake (if equipped)
C15 and C18 Industrial Engines Sensor Signal (Analog, Passive) - Test
C7 and C9 Petroleum Engines Sensor Signal (Analog, Active) - Test
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
2007/06/04 A Dye is Now Added to the Engine Oil at the Factory {1348}
C6.6 Industrial Engine Belt Tensioner - Inspect
C7 and C9 Petroleum Engines Injector Solenoid - Test
C7 and C9 Petroleum Engines Injection Actuation Pressure Control Valve - Test
C15 and C18 Industrial Engines Sensor Supply - Test
3512C Engine Plate Locations and Film Locations
3512C Engine Injector Solenoid - Test
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Priming Pump and Fuel Filter Base - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Lines - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector Cover - Remove and Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injector - Install
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Remove
C4.4 (MECH) Industrial Engine and Generator Sets Fuel Injection Pump Gear - Install
3512C Industrial Engine Electric Starting Motor - Remove and Install
C7 and C9 Petroleum Engines Sensor Signal (Analog, Passive) - Test
C32 Marine Propulsion Engines Exhaust Temperature Is High