Exhaust Manifold - Remove and Install
Removal Procedure
Start By:
- Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove elbow assembly (4) .
Show/hide table
Illustration 1 | g01361806 |
- Disconnect riser assembly (1) . Position riser assembly (1) out of the way of exhaust manifold (3) . Remove bracket (5) and disconnect tube assembly (6) .
- Remove nuts (2) , the washers, and the spacers.
- Remove exhaust manifold (3) .
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 5P-3931     | Anti-Seize Compound     | -     |
- Apply Tooling (A) to the studs prior to assembly. If necessary, install the studs and tighten to a torque of 35 ± 5 N·m (26 ± 4 lb ft).
Show/hide table
Illustration 2 | g01361806 |
Show/hide table
Illustration 3 | g01857657 |
- Position exhaust manifold (3) on the engine.
- Install the spacers, the washers, and nuts (2) . Tighten nuts (2) in a numerical sequence to a torque of 38 ± 5 N·m (28 ± 4 lb ft).
- Connect riser assembly (1) . Install elbow assembly (4) .
- Connect tube assembly (6) . Install bracket (5) .
End By: Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
Caterpillar Information System:
C32 Marine Propulsion Engines Injector Solenoid - Test
C9 Agricultural Engine for Challenger Tractors Air Inlet Heater - Test
Starting Motor - Delco 50-MT Starting Motor
CX28 On-Highway Transmission Oil Filter and Base (Power Train) - Remove and Install
C9 Agricultural Engine for Challenger Tractors Component Location
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Remove
Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130} Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130}
C32 Marine Engines Fuel Filter Base - Remove and Install
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Diagnostic Trouble Code List
C9 Agricultural Engine for Challenger Tractors Power Is Intermittently Low or Power Cutout Is Intermittent
Starting Motor - Delco 50-MT Normal Operation
C3.4 IND Industrial Engine Maintenance Interval Schedule
3512B Marine Auxiliary Engine Engine Oil and Filter - Change
Contaminated Oil Related Component Failures in Light Armored Vehicles That Are Powered by 3126 Engines{1308} Contaminated Oil Related Component Failures in Light Armored Vehicles That Are Powered by 3126 Engines{1308}
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Install
C18 Marine Auxiliary Engines Electrical Power Supply - Test
C32 Marine Engines Engine Oil Filter Base
C4.4 (Mech) Industrial Engine Engine Oil and Filter - Change
CX28 On-Highway Transmission Torque Converter - Remove
C32 Marine and Auxiliary Marine Engines Engine Oil Filter Base - Remove
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System System Schematic
CX28 On-Highway Transmission Torque Converter - Install
C9 On-highway Engine Clean Gas Induction Valve - Remove
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Transmission, SPN 117 - FMI 2