Fuel Filter Base - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 185-3630 | Strap Wrench Assembly | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to remove fuel filters (2) from fuel filter base (1).
Show/hide table
Illustration 2 g01361613 - Disconnect hose assemblies (4), (8), and (9) from fuel filter base (1). Immediately cap all openings or plug all openings in order to prevent contamination.
- Disconnect harness assemblies (3) and (5) from fuel filter base (1).
- Remove bolts (7), the washers, and the nuts. Remove fuel filter base (1) from bracket (6).
Show/hide table
| |
| Illustration 1 | g01361586 |
- Position fuel filter base (1) on bracket (6). Install bolts (7), the washers, and the nuts.
- Connect hose assemblies (4), (8), and (9) to fuel filter base (1).
- Connect harness assemblies (5) and (3) to fuel filter base (1).
Show/hide table
Illustration 4 g01361586 - Install fuel filters (2) on fuel filter base (1). Refer to the Operation and Maintenance Manual, "Fuel System Secondary Filter - Replace" topic for more information.
- Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System - Prime" topic for more information.
Show/hide table
| |
| Illustration 3 | g01361613 |
Caterpillar Information System:
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Diagnostic Trouble Code List
C9 Agricultural Engine for Challenger Tractors Power Is Intermittently Low or Power Cutout Is Intermittent
Starting Motor - Delco 50-MT Normal Operation
C3.4 IND Industrial Engine Maintenance Interval Schedule
C9 Agricultural Engine for Challenger Tractors Engine Top Speed Is Not Obtained
C3.4 IND Industrial Engine Reference Material
C4.4 and C6.6 Engines for Caterpillar Built Machines Fuel Rail Pump Solenoid - Test
C3.4 IND Industrial Engine Engine Valve Lash - Inspect/Adjust
C4.4 (Mech) Industrial Engine Crankcase Breather (Canister) - Replace
3176C, 3406E and 3456 Industrial Engines Engine Stalls at Low RPM
Starting Motor - Delco 50-MT Starting Motor - Assemble
Starting Motor - Delco 50-MT Starting Motor - Disassemble
Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130} Tightening Procedure for the Studs of the Variable Valve Actuator for 735 and 740 Articulated Trucks and C15 On-highway Truck Engine{1130}
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Remove
C9 Agricultural Engine for Challenger Tractors Component Location
CX28 On-Highway Transmission Oil Filter and Base (Power Train) - Remove and Install
Starting Motor - Delco 50-MT Starting Motor
C9 Agricultural Engine for Challenger Tractors Air Inlet Heater - Test
C32 Marine Propulsion Engines Injector Solenoid - Test
C32 Marine and Auxiliary Marine Engines Exhaust Manifold - Remove and Install
3512B Marine Auxiliary Engine Engine Oil and Filter - Change
Contaminated Oil Related Component Failures in Light Armored Vehicles That Are Powered by 3126 Engines{1308} Contaminated Oil Related Component Failures in Light Armored Vehicles That Are Powered by 3126 Engines{1308}
C9.3 Engines for Caterpillar Built Machines Cylinder Head - Install
C18 Marine Auxiliary Engines Electrical Power Supply - Test