Window Wiper and Wiper Motor (Front) - Remove and Install
Show/hide table
Illustration 1 | g03657000 |
Show/hide table
Specification for 398-8841 Window Wiper and Washer | |||
Item | Qty | Part | Specification Description |
1 | 1 | 269-0413 Window Wiper Arm Gp | The arm tension is |
2 | 1 | 6V-7419 Wiper Blade | Torque to |
3 | 1 | 134-1934 Window Wiper Arm As | Use following procedure to install wiper arm.
Torque to Wait for minimum 0.5 hours. Again tighten to |
Show/hide table
Illustration 2 | g03657004 |
241-9102 Window Wiper Motor Gp
Show/hide table
Item | Qty | Part | Specification Description |
B | - | - | Wiping angle from automatic parking position is 60 ± 2 degrees. |
4 | 3 | Bolt | Torque to |
5 | 2 | Nut | Torque to |
6 | 2 | 5C-7261 Nut | Use following procedure to install wiper arm.
Torque to Wait for minimum 0.5 hour to 4 hours maximum. Again tighten to |
Show/hide table
Illustration 3 | g03657006 |
330-5025 Window Wiper Motor Gp
Show/hide table
Item | Qty | Part | Specification Description |
D | - | - | Wiping angle from automatic parking position is 130 ± 3 degrees. |
7 | - | - | Use the following tightening procedure to tighten the nut:
If mounted in glass, tighten the nut to If mounted in steel, tighten the nut to |
8 | - | - | Use the following tightening procedure to tighten the nut:
If mounted in glass, tighten the nut to If mounted in steel, tighten the nut to |
9 | 1 | 5C-7261 Nut | Use following procedure to install wiper arm.
Torque to Wait for minimum 0.5 hour to 4 hours maximum. Again tighten to |
- Articulate the machine to the left. Install wood blocks on all four wheels. The blocks will prevent movement. The articulation of the machine will allow access to the window wiper motor.
- Move the battery disconnect switch to the OFF position. Disconnect both battery terminals.
Show/hide table
Illustration 4 g01427195 - Unlock cover (1) in order to open cover (1).
Show/hide table
Illustration 5 g01427186 - Raise covers (2).
- Remove nuts (3).
- Remove hose (4) from wiper arm (5).
- Remove both wiper arms (5).
Note: Check wiper arms (5) for wear.
Show/hide tableIllustration 6 g01427201 - Remove covers (6).
Show/hide table
Illustration 7 g01427203 - Remove bolts (7) from plate assembly (8).
Show/hide table
Illustration 8 g01427227 - Remove hose (10) from plate assembly (8). Disconnect harness assembly (9).
Show/hide table
Illustration 9 g03650508 - Remove nuts (11). Remove window wiper motor (12).
- Install window wiper motor (12) and wiper arms (5) in the reverse order of removal.
- Tighten nuts (11) to a torque of
38 ± 2 N·m (28 ± 1 lb ft) . - Tighten nuts (3) to a torque of
23 ± 1 N·m (204 ± 9 lb in) . Wait at least half an hour. Tighten nuts (3) again to23 ± 1 N·m (204 ± 9 lb in) .
- Tighten nuts (11) to a torque of
Caterpillar Information System:
621K, 623K and 627K Wheel Tractor-Scrapers Machine Systems Steering Cylinder - Remove and Install
953K and 963K Track-Type Loaders Engine Crankcase Breather Filter - Replace
980L Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Differential and Bevel Gear
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Inlet Module (Catalyst) - Remove and Install
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Catalyst (SCR) - Remove and Install
2014/09/26 A New Guardrail Group Is Now Used on Certain D8T Track-Type Tractors {7150, 7256}
525D, 535D, 545D and 555D Wheel Skidders Diagnostic Trouble Codes
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Solenoid Valve (DEF Heater Coolant) - Remove and Install
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Voltage Control (Load Protection) - Remove and Install
2014/09/18 New Engine Enclosure Doors are Now Used on Certain D8R Track-Type Tractors {7263}
980M and 982M Wheel Loaders Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Cylinder
2014/09/01 New Hood Panel Group Is Now used on Certain D8R Track-Type Tractors {7251, 7263}
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Temperature Sensor (Catalyst Inlet) - Remove and Install
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Electronic Control (Aftertreatment) - Remove and Install
953K and 963K Track-Type Loaders Engine Oil Level - Check
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Exhaust Cooler (NRS) - Remove and Install
621K, 623K and 627K Wheel Tractor-Scrapers Engine Supplement Exhaust Gas Valve (NRS) - Remove and Install
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Sprocket - Inspect
910K and 914K Compact Wheel Loaders Electrohydraulic System Sensor Signal (Analog, Active) - Test
953K and 963K Track-Type Loaders Engine Oil and Filter - Change
990K Wheel Loader Machine Systems Differential Pinion Preload - Adjust
2014/08/08 An Improved Latch Group for the Cab Door Is Now Used on Certain D6N Track-Type Tractors {7301, 7308}
2014/03/21 New Stop and Tail Lamp Gp Is Now Used on Certain H-Series Medium Wheel Loaders {1432}
953K and 963K Track-Type Loaders Cab - Tilt