Diagnostic Trouble Code List
Use the instrument cluster or use the Caterpillar Electronic Technician (Cat ET) in order to determine the diagnostic codes for the Transmission ECM. After determining the diagnostic codes, refer to the corresponding test procedure for more information. Perform the procedure that corresponds with the correct diagnostic code. The following table is a list of possible diagnostic codes for the Transmission ECM.
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
Diagnostic Codes For The Transmission ECM for Versatile | |
---|---|
For troubleshooting, see the procedure with the same "CID" and "FMI". | |
"CID"/FMI | Description |
CID 0177 Parking Brake Pressure Switch | |
FMI 03 | Transmission Oil Temperature Sensor Short to Battery/Open Circuit |
FMI 04 | Transmission Oil Temperature Sensor Short to Ground |
CID 0262 5 Volt Sensor Supply Voltage | |
FMI 03 | Voltage above normal |
FMI 04 | Voltage below normal |
CID 0269 10 Volt Sensor Supply | |
FMI 03 | 10 Volt Sensor Supply Short To +Battery |
FMI 04 | 10 Volt Sensor Supply Short To Ground |
CID 0473 Charge pressure sensor | |
FMI 03 | Voltage above normal or shorted high |
FMI 04 | Voltage below normal or shorted low |
CID 0573 Inching Pedal Position Sensor | |
FMI 00 | Data valid but above normal operational range |
FMI 01 | Data valid but below normal operational range |
FMI 08 | Abnormal frequency, pulse width, or period |
CID 0585 Transmission Output Speed Sensor #1 | |
FMI 12 | Bad component |
CID 0669 Transmission Input Speed Sensor | |
FMI 02 | Data that is erratic, intermittent, or incorrect |
CID 0673 Transmission Output Speed Sensor #2 | |
FMI 12 | Bad component |
CID 1401 Transmission Clutch Solenoid #1 | |
FMI 03 | Voltage above normal or shorted high |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1402 Transmission Clutch Solenoid #2 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1403 Transmission Clutch Solenoid #3 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1404 Transmission Clutch Solenoid #4 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1405 Transmission Clutch Solenoid #5 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1406 Transmission Clutch Solenoid #6 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1407 Transmission Clutch Solenoid #7 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1408 Transmission Clutch Solenoid #8 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1409 Transmission Clutch Solenoid #9 | |
FMI 03 | Voltage above normal |
FMI 05 | Current below normal or open circuit |
FMI 06 | Current above normal or closed circuit |
CID 1484 Inching Pedal Switch | |
FMI 02 | Data that is erratic, intermittent, or incorrect |
FMI 07 | Mechanical system not responding properly |
Show/hide table
Diagnostic Codes For The Transmission ECM for Versatile | |
---|---|
For troubleshooting, see the procedure with the same "SPN" and "FMI". | |
"SPN"/FMI | Description |
SPN 127 Transmission Oil Pressure Sensor | |
FMI 3 | Voltage above normal |
FMI 4 | Data valid but above normal operating range (moderate severity) |
SPN 161 Transmission Input Speed Sensor | |
FMI 2 | Data that is erratic, intermittent, or incorrect |
SPN 177 Transmission Oil Temperature Sensor | |
FMI 3 | Voltage above normal |
FMI 4 | Voltage below normal |
SPN 191 Transmission Output Speed Sensor #1 | |
FMI 12 | Speed failure |
SPN 701 Transmission Clutch Solenoid #9 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 702 Inching Pedal Switch | |
FMI 2 | Data that is erratic, intermittent, or incorrect |
FMI 7 | Not responding |
SPN 703 Inching Pedal Position Sensor | |
FMI 0 | Voltage above normal |
FMI 1 | Current below normal or open circuit |
FMI 8 | Current above normal or closed circuit |
SPN 704 Transmission Output Speed #2 | |
FMI 12 | Bad device or component |
SPN 734 Transmission Clutch Solenoid #1 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 735 Transmission Clutch Solenoid #2 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 736 Transmission Clutch Solenoid #3 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 737 Transmission Clutch Solenoid #4 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 738 Transmission Clutch Solenoid #5 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 739 Transmission Clutch Solenoid #6 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 1079 5 Volt Sensor Supply Voltage | |
FMI 3 | Voltage above normal |
FMI 4 | Voltage below normal |
SPN 1542 10 Volt Sensor Supply Voltage | |
FMI 3 | 10 Volt Sensor Supply Short To +Battery |
FMI 4 | 10 Volt Sensor Supply Short To Ground |
SPN 2905 Transmission Clutch Solenoid #7 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
SPN 2906 Transmission Clutch Solenoid #8 | |
FMI 3 | Voltage above normal |
FMI 5 | Current below normal or open circuit |
FMI 6 | Current above normal or closed circuit |
Caterpillar Information System:
TA19 and TA22 Transmissions Power Train Electronic Control System Transmission
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Machine Preparation for Troubleshooting
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System Connector Locations
TA19-M2WD and TA19-M4WD (Delta) Agricultural Transmission Power Train Electronic Control System General Information
VR6 Voltage Regulator Low Voltage
VR6 Voltage Regulator General Information
VR6 Voltage Regulator Power Factor Regulation and KVAR Regulation
VR6 Voltage Regulator Series Boost
VR6 Voltage Regulator Cross Current Compensation
VR6 Voltage Regulator Voltage Droop Control
3500 Engines Air Starting Valve
3054E and 3056E Industrial Engines and Engines for Caterpillar Built Machines Throttle Switch Circuit - Test
VR6 Voltage Regulator High Voltage
3512C and 3516C Marine Auxiliary and Generator Set Engines Flexible Coupling - Inspect
3500 Engines Air Lines
3500 Engines Air Inlet and Exhaust Lines
VR6 Voltage Regulator Droop - Adjust
3500 Industrial Engines Exhaust Flange
C280 Marine and Petroleum Engines Engine Governing - Adjust
VR6 Voltage Regulator Voltage Regulator - Test
TA19 and TA22 Transmissions Power Train Electronic Control System Parameters
TA19 and TA22 Transmissions Power Train Electronic Control System Connector Contact Description
TA19 and TA22 Transmissions Power Train Electronic Control System System Schematic
G3408C and G3412C Engines Water Temperature Regulator