Fuel Tank - Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7575 | Link Brackets | 2 |
| B | 138-7575 | Link Brackets | 3 |
- Attach Tooling (B) and a suitable lifting device to fuel tank (22). The weight of fuel tank (22) is approximately
998 kg (2200 lb) . Use Tooling (B) and the suitable lifting device in order to position fuel tank (22) to the machine. - Install the washers and bolts (24). Install the washers and bolts (23). Install the washers and bolts (21).
Show/hide table
Illustration 4 g02947779 - Pull harness assembly (17) through grommet (20). Connect harness assembly (17). Attach cable strap (19). Connect all clips (18) that secure harness assembly (17) to the fuel tank.
Show/hide table
Illustration 5 g02947776 - Install guard (16).
Show/hide table
Illustration 6 g02947743 - Attach Tooling (A) and a suitable lifting device to platform (10). The weight of platform (10) is approximately
64 kg (140 lb) . Use Tooling (A) and the suitable lifting device in order to position platform (10) to the machine. Install the washers and bolts (15).Show/hide table
Illustration 7 g02947736 - Install the washers and bolts (14).
Show/hide table
Illustration 8 g02947732 - Install the washers, bolt (13) and bolts (12) to platform (10). Install cover (11).
Show/hide table
Illustration 9 g02947746 - Install bolt (9).
Show/hide table
Illustration 10 g02947726 - Use two people in order to install platform (8). The weight of platform (8) is approximately
28 kg (62 lb) .Show/hide table
Illustration 11 g02947720 - Install handrails (7).
Show/hide table
Illustration 12 g02947696 - Install panel (6).
Show/hide table
Illustration 13 g02947717 - Install bolt (5) to the brace. Repeat this step for the opposite side.
Show/hide table
Illustration 14 g02947671 - Attach a suitable lifting device to ladder assembly (4). The weight of ladder assembly (4) is approximately
30 kg (66 lb) . Use the suitable lifting device in order to position ladder assembly (4) to the machine. Install the bolts.Show/hide table
Illustration 15 g02947139 - Install clips (3). Install the fittings and valves (2). Install tube assembly (1).
- Fill the fuel tank. Refer to Operation and Maintenance Manual, "Fuel Tank Water and Sediment - Drain" and Operation and Maintenance Manual, "Capacities (Refill)" for the correct draining and filling procedures.
Show/hide table
| |
| Illustration 1 | g02948737 |
Show/hide table
| |
| Illustration 2 | g02949338 |
Show/hide table
| |
| Illustration 3 | g02949341 |
End By:
- Install the fuel priming pump and fuel filter base.
- Install the fuel heater.
Caterpillar Information System:
2012/03/28 A New Coolant Conditioner Is Now Available {1350, 1352, 1395}
Thermal Spray Procedures for Torque Converter Input Housing {0679, 3101, 3127} Thermal Spray Procedures for Torque Converter Input Housing {0679, 3101, 3127}
2012/03/28 A New Coolant Conditioner Is Now Available {1350, 1352, 1395}
Thermal Spray Procedures for Splined Shaft{0679, 3101} Thermal Spray Procedures for Splined Shaft{0679, 3101}
Thermal Spray Procedures for Torque Converter Carrier - Seal Ring Bore {0374, 0599, 0679, 3101, 3135} Thermal Spray Procedures for Torque Converter Carrier - Seal Ring Bore {0374, 0599, 0679, 3101, 3135}
Thermal Spray Procedures for Torque Converter Carrier - Taper Bearing Diameter{0679, 3101, 3125} Thermal Spray Procedures for Torque Converter Carrier - Taper Bearing Diameter{0679, 3101, 3125}
2012/08/24 The Actuator for Air Conditioner Group and Cab Heater Group Is Now Improved on Certain Track-Type Loaders and Track-Type Tractors {7304, 7320}
Thermal Spray Procedures for Transmission, Torque Converter and Torque Divider Shafts {0679, 0719, 3030, 3101, 3125, 3130} Thermal Spray Procedures for Transmission, Torque Converter and Torque Divider Shafts {0679, 0719, 3030, 3101, 3125, 3130}
D6K2 Track-Type Tractor Engine Supplement Hood - Remove and Install
950H Wheel Loader and 962H Wheel Loader Electrohydraulic System ECM Location Code - Test
Custom Product Support Literature for 980K Wheel Loaders That Are Equipped with the 330-4870 Steel Mill Arrangement {0374, 7000} Custom Product Support Literature for 980K Wheel Loaders That Are Equipped with the 330-4870 Steel Mill Arrangement {0374, 7000}
Thermal Spray Procedures for Torque Converter Impeller {0679, 3101, 3134} Thermal Spray Procedures for Torque Converter Impeller {0679, 3101, 3134}
D5R Track-Type Tractor Capacities (Refill)
Failures of the 305-6843 Guide Spring on Certain Engines{1102, 1121, 1123, 1209} Failures of the 305-6843 Guide Spring on Certain Engines{1102, 1121, 1123, 1209}
950H Wheel Loader and 962H Wheel Loader Power Train Input Transfer Gears
Thermal Spray Procedures for Exhaust Manifold (I.D. ; O.D.){0679, 1059} Thermal Spray Procedures for Exhaust Manifold (I.D. & O.D.){0679, 1059}
2012/08/29 An Improved Lip Type Seal Within the Steering Valve Group is Now Used on Certain Wheel Tractor Scrapers {4307}
Thermal Spray Procedures for Tyrone Drive Shaft (Pump Gear){0679, 3066, 5073} Thermal Spray Procedures for Tyrone Drive Shaft (Pump Gear){0679, 3066, 5073}
D5R Track-Type Tractor Access Doors and Covers
Thermal Spray Procedures for Hydraulic Swivel {0679, 5060} Thermal Spray Procedures for Hydraulic Swivel {0679, 5060}
Instructions for Bonding Non-Metallic Components {7301, 7305} Instructions for Bonding Non-Metallic Components {7301, 7305}
Thermal Spray Procedures for Steering Clutch Housing{0679, 4100, 4101} Thermal Spray Procedures for Steering Clutch Housing{0679, 4100, 4101}
Thermal Spray Procedures for Wheel Loader Trunnion Support {0679, 3260, 3268} Thermal Spray Procedures for Wheel Loader Trunnion Support {0679, 3260, 3268}
Thermal Spray Procedures for Brake Piston Housing {0679, 4251} Thermal Spray Procedures for Brake Piston Housing {0679, 4251}