Implement Control Valve - Assemble
Assembly Procedure.
- Install O-ring seal (82), fitting (81) , and dust cap (80) .
Show/hide table
Illustration 1 | g02277634 |
- Install O-ring seal (85), fitting (84), and dust cap (83) .
- Install O-ring seal (89) and plug (88) into manifold (49). Install O-ring seal (87) and plug (86) .
- Install nut (62), retainer (63), washer (64), seal (65), spring (66), plate (67), plunger 68, O-ring seal (69), and O-ring seal (70) into valve (50) .
Show/hide table
Illustration 2 | g02277574 |
- Install cap (71), O-ring seal (72), shims (73), plunger (79), spring (78), and seals (77), (76), (75), and (74) into valve (51) .
- Install valve (61), backup ring (60), O-ring seal (59), ball (58), spring (57), pin (56), and O-ring seal (55) into orifice (52) .
Show/hide table
Illustration 3 | g02277573 |
- Install O-ring seal (53), valve assembly (50) and (51), orifice (52), fittings (54), and into manifold assembly (49) .
Show/hide table
Illustration 4 | g02277533 |
- Install bolts (48) into manifold assembly (49) .
Show/hide table
Illustration 5 | g02277513 |
- Install O-ring seals (34) and orifice (33) into valve (18) .
Show/hide table
Illustration 6 | g02277413 |
- Install plug (39), O-ring seals (40) and (41), backup ring (42), spring (43), and valve (44) .
- Install backup rings (35), O-ring seal (37) and (36) and plug (38) .
- Install O-ring seals (29), cartridge assembly (30) coil assembly (31) and nut (32) .
Show/hide table
Illustration 7 | g02277256 |
- Install dust cap (20), fitting (21), O-ring seal (22), into valve (23).
Show/hide table
Illustration 8 | g02277273 |
- Install retainer (24), spring (25), retainer (26), and O-ring seals (27) into valve (18) .
- Repeat Steps 13 through 14 for the opposite end of valve.
- Install spool (28) into valve (18) .
- Install solenoid assembly (19). Install valve assembly (18). Install bolts (17) .
Show/hide table
Illustration 9 | g02276156 |
- Install plug (13), O-ring seal (14), spring (15), and valve (16) from opposite side of valve assembly (6) .
Show/hide table
Illustration 10 | g02276155 |
- Install O-ring seal (9) onto cover (8). Install piston (10), spring (11), and spool (12) .
Show/hide table
Illustration 11 | g02276135 |
Show/hide table
Illustration 12 | g02276133 |
- Install cover (8) and bolts (7) .
- Install dozer lift valve (47) .
Show/hide table
Illustration 13 | g02277495 |
- Repeat Steps 12 through 20 to assemble dozer tilt valve (46) .
Show/hide table
Illustration 14 | g02277484 |
- Install dozer tilt valve (46) .
- Repeat Steps 12 through 20 to assemble dozer tilt valve (45) .
Show/hide table
Illustration 15 | g02277414 |
- Install ripper lift valve (45)
- Repeat Steps 12 through 20 to assemble dozer tilt valve (45) .
Show/hide table
Illustration 16 | g02275961 |
- Install ripper tip valve assembly (6) .
- Install O-ring seals (3), (4), and (5) .
Show/hide table
Illustration 17 | g02275967 |
- Install cover (2). Install nuts (1). Tighten nuts (1) to a torque of 105 ± 10 N·m (78 ± 7 lb ft)
Show/hide table
Illustration 18 | g02275966 |
End By: Install implement control valve.
Caterpillar Information System:
D6N Track-Type Tractor Operation Information
Procedure For Blade Solenoid Calibrations on Certain Track-Type Tractors{0785, 5479, 7610} Procedure For Blade Solenoid Calibrations on Certain Track-Type Tractors{0785, 5479, 7610}
D11T Track-Type Tractor Power Train Data Link
320E and 323E Excavators Machine System Specifications Refrigerant Compressor
966K XE Wheel Loader Machine Systems Piston Pump (Brake, Pilot, Fan) - Disassemble
D6N Track-Type Tractor Monitoring System
966K XE Wheel Loader Machine Systems Piston Pump (Brake, Pilot, Fan) - Assemble
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head - Remove and Install
D11T Track-Type Tractor Power Train Electrical Output Components
D11T Track-Type Tractor Power Train Electronic Control Module
D6N Track-Type Tractor Declaration of Conformity
D6N Track-Type Tractor Plate Locations and Film Locations
(Custom) Pipe and Pole Forks Daily Inspection
C27 and C32 Engines for Caterpillar Built Machines Configuration Parameters
2010/12/06 A New Throttle Actuator Is Used for Some G3500 and G3500B Engines {1265, 1716}
C27 and C32 Engines for Caterpillar Built Machines Component Location
C6.6 Industrial Engine Exhaust Back Pressure Valve - Remove and Install
2010/12/24 New Relief Valve Groups Are Now Used for the Bucket Tilt on Certain Wheel Loaders {5051}
966K XE Wheel Loader Steering System Secondary Steering Pump and Electric Motor
966K Wheel Loader and 972K Wheel Loader Steering System Secondary Steering Valve
854K Wheel Dozer and 992K Wheel Loader Engine and Torque Converter - Remove
966K XE Wheel Loader Power Train Pump and Motor - Remove and Install
Cat® Grade Control for Wheel Tractor Scrapers Configuration
C9.3 Tier 4 Final Engines Turbocharger