Air Tank - Remove
Removal Procedure
Start By:
- Purge the air system. Refer to Disassembly and Assembly, "Air System - Purge".
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.
- Disconnect hose assembly (1). Disconnect harness assemblies (2) and harness assembly (3). Disconnect hose assemblies (4) .
Show/hide table
Illustration 1 | g02191574 |
- Disconnect harness assembly (5).
Show/hide table
Illustration 2 | g02191597 |
- Remove bolt (6) in order to remove pressure sensor (7) .
Show/hide table
Illustration 3 | g02191604 |
- Disconnect hose assemblies (8). Disconnect fitting (9) .
Show/hide table
Illustration 4 | g02191608 |
- Remove panel (10) .
Show/hide table
Illustration 5 | g02191614 |
- Attach Tooling (A) and a suitable lifting device onto air tank (11). The weight of air tank (11) is approximately 147 kg (325 lb). Remove bolts (12). Remove air tank (11) .
Show/hide table
Illustration 6 | g02191981 |
Caterpillar Information System:
966K Wheel Loader and 972K Wheel Loader Power Train Speed Sensor (Transmission Output)
2010/09/13 Procedures are Available for Replacing Base Edge Assemblies, Repairing Adapter Weld, and Edge Assembly Cracks on Large Wheel Loader Buckets {6101, 6102, 6131, 6132, 6801, 6818}
Procedure for Replacement of the Transmission Shift Lever or Hoist Lever Sensor on Certain Off-Highway Trucks and Articulated Trucks{3065, 5063, 5737} Procedure for Replacement of the Transmission Shift Lever or Hoist Lever Sensor on Certain Off-Highway Trucks and Articulated Trucks{3065, 5063, 5737}
966K Wheel Loader and 972K Wheel Loader Power Train Speed Sensor (Torque Converter Output)
966K Wheel Loader and 972K Wheel Loader Power Train Torque Converter and Pump Drive Housing
C27 and C32 Engines for Caterpillar Built Machines Event Codes
C27 and C32 Engines for Caterpillar Built Machines Diagnostic Trouble Codes
D8T Track-Type Tractor Engine Supplement Electronic Control Module (ECM) - Remove and Install
D6T Track-Type Tractor Power Train Location of Electrical Components
C4.4 Industrial Engine Mounting and Dismounting
2010/07/28 Correction to Systems Operation Testing and Adjusting , "Suspension System (Front) - Purge and Charge" {7201, 7201, 7218}
Diagnosing Fuel Dilution of Engine Oil for C27 and C32 Engines{1101, 1124, 1251, 1280, 1290} Diagnosing Fuel Dilution of Engine Oil for C27 and C32 Engines{1101, 1124, 1251, 1280, 1290}
994H Wheel Loader Engine Supplement Air Tank - Install
320E and 323E Excavators Hydraulic System Relief Valve (Line)
966K Wheel Loader and 972K Wheel Loader Power Train Transmission Oil Pump
320E and 323E Excavators Hydraulic System Check Valve (Load)
966K Wheel Loader and 972K Wheel Loader Braking and Hydraulic Fan System General Information (Brake, Hydraulic Fan System)
D11T Track-Type Tractor MID 082 - CID 0590 - FMI 09
D8T and D9T Track-Type Tractors MID 082 - CID 0600 - FMI 03
C27 and C32 Engines for Caterpillar Built Machines Engine Shutdown While Idling
G3304B and G3306B Engines Catalytic Converter Has High Outlet Temperature
D8T and D9T Track-Type Tractors MID 082 - CID 0600 - FMI 04
D11T Track-Type Tractor MID 082 - CID 0869 - FMI 03
D11R Track-Type Tractor Starting with Auxiliary Start Receptacle