Electronic Unit Injector Sleeve - Install
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6891     | Injector Tool Group     | 1     |
B     | 9U-6862     | Tapered Brush     | 1     |
9U-6863 | Small Bore Brush     | 1     | |
9U-7244 | End Brush     | 1     | |
9U-7237 | Brush Extension     | 1     | |
4C-5552 | Large Bore Brush     | 1     | |
C     | 4C-9507     | Retaining Compound     | -     |
- Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
- Install new O-ring seals (2) and (3) on electronic unit injector sleeve (1) .
Show/hide table
NOTICE |
---|
Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris. |
Show/hide table
Illustration 1 | g01261773 |
- Apply a thin coat of Tooling (C) to the contact surface of electronic unit injector sleeve (1) at the area that is Marked "X".
Note: Do not apply Tooling (C) to the cylinder head surfaces. Apply Tooling (C) on the electronic unit injector sleeve only.
- Lubricate O-ring seals (2) and (3) with clean engine oil.
- Install Tooling (A) into the threads of electronic unit injector sleeve (1) .
Show/hide table
Illustration 2 | g01261802 |
- Position Tooling (A) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seal on the electronic unit injector sleeve.
- Use Tooling (A) and a hammer to install electronic unit injector sleeve (1) in the cylinder head.
Show/hide table
NOTICE |
---|
Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head. |
- Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the cooling system capacity. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure.
End By: Install the electronic unit injector. Refer to Disassembly and Assembly , "Electronic Unit Injector - Install".
Caterpillar Information System:
C7 On-Highway Engine Fuel Manifold (ARD) - Install
CX31 On-Highway Transmission Gear Pump (Transmission)
C13 Engine Electronic Unit Injector Sleeve - Remove
C13 and C15 On-highway Engines Engine/Gear Parameters
C13 Engine Electronic Unit Injector - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 735 - FMI 3
C7 PETROLEUM Petroleum Engine Air Compressor - Remove and Install
C7 On-Highway Engine Fuel Manifold (ARD) - Remove
793F and 793F CMD Off-Highway Truck Automatic Lubrication System Automatic Lubrication System - Test
C7 PETROLEUM Petroleum Engine Electric Starting Motor - Remove and Install
C13 Engine Fuel Transfer Pump - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 734 - FMI 3
2006/04/17 New Speed Timing Sensor Available {1912}
2006/06/01 An Improved Speed-Timing Sensor is Now Available {1912}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 736 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 737 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 738 - FMI 3
C7 and C9 On-Highway Engines Timer Parameters
G3406 Engine Engine Auxiliary Sump Oil - Change
C11 and C13 Petroleum Engines Rocker Arm and Shaft - Remove
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 740 - FMI 3
C11 and C13 Petroleum Engines Rocker Arm and Shaft - Install
CX28 On-Highway Transmission Relief Valve (Torque Converter Outlet) Pressure - Test and Adjust
C4.4 Industrial Engine Belt Tension Chart