Electronic Unit Injector Sleeve - Remove
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 9U-6891     | Injector Tool Group     | 1     |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change".
- Install Tooling (A) into electronic unit injector sleeve (1) .
Show/hide table
Illustration 1 | g01261663 |
- Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head assembly.
- Remove electronic unit injector sleeve (1) .
Show/hide table
Illustration 2 | g01261681 |
Caterpillar Information System:
C13 and C15 On-highway Engines Engine/Gear Parameters
C13 Engine Electronic Unit Injector - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 735 - FMI 3
C7 PETROLEUM Petroleum Engine Air Compressor - Remove and Install
C7 On-Highway Engine Fuel Manifold (ARD) - Remove
793F and 793F CMD Off-Highway Truck Automatic Lubrication System Automatic Lubrication System - Test
C7 PETROLEUM Petroleum Engine Electric Starting Motor - Remove and Install
C13 Engine Fuel Transfer Pump - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 734 - FMI 3
C7 On-highway Engine Fuel Control Manifold - Aftertreatment Regeneration Device
C7 PETROLEUM Petroleum Engine Alternator - Remove and Install
C7 On-Highway Engine Oil Manifold - Remove and Install
CX31 On-Highway Transmission Gear Pump (Transmission)
C7 On-Highway Engine Fuel Manifold (ARD) - Install
C13 Engine Electronic Unit Injector Sleeve - Install
2006/04/17 New Speed Timing Sensor Available {1912}
2006/06/01 An Improved Speed-Timing Sensor is Now Available {1912}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 736 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 737 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 738 - FMI 3
C7 and C9 On-Highway Engines Timer Parameters
G3406 Engine Engine Auxiliary Sump Oil - Change
C11 and C13 Petroleum Engines Rocker Arm and Shaft - Remove
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 740 - FMI 3