Fuel Manifold (ARD) - Remove
Removal Procedure
Start By:
- Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
- Remove the oil manifold. Refer to Disassembly and Assembly, "Oil Manifold - Remove and Install".
- Remove cable straps (1). Disconnect harness assembly (3). Disconnect tube assembly (2) .
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Note: Plug all hose assemblies and all tube assemblies.
Show/hide table
Illustration 1 | g01261486 |
- Remove bolt (4) and bolt (5) in order to position tube assembly (2) out of the way.
Show/hide table
Illustration 2 | g01261488 |
- Disconnect tube assembly (6). Remove tube assembly (7). Disconnect tube assembly (8). Remove bolt (11). Remove tube assembly (8). Disconnect tube assemblies (9) and (10) .
Show/hide table
Illustration 3 | g01261490 |
Show/hide table
Illustration 4 | g01261491 |
- Remove bolts (12) and (13). Remove nut (15). Reposition fuel manifold (14) .
Show/hide table
Illustration 5 | g01261494 |
- Disconnect harness assemblies (16) and (17). Remove fuel manifold (14) .
Show/hide table
Illustration 6 | g01261496 |
Caterpillar Information System:
793F and 793F CMD Off-Highway Truck Automatic Lubrication System Automatic Lubrication System - Test
C7 PETROLEUM Petroleum Engine Electric Starting Motor - Remove and Install
C13 Engine Fuel Transfer Pump - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 734 - FMI 3
C7 On-highway Engine Fuel Control Manifold - Aftertreatment Regeneration Device
C7 PETROLEUM Petroleum Engine Alternator - Remove and Install
C7 On-Highway Engine Oil Manifold - Remove and Install
325D and 329D Excavators and 325D Material Handler Machine System Specifications Manifold and Reducing Valve (Pilot Oil)
C7 and C9 On-Highway Engines Dedicated PTO Parameters
C7 On-Highway Engine Air Compressor - Remove and Install
3500B and 3500C Locomotive Engines Injector Solenoids
3500B and 3500C Locomotive Engines System Configuration Parameters
C7 PETROLEUM Petroleum Engine Air Compressor - Remove and Install
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 735 - FMI 3
C13 Engine Electronic Unit Injector - Remove and Install
C13 and C15 On-highway Engines Engine/Gear Parameters
C13 Engine Electronic Unit Injector Sleeve - Remove
CX31 On-Highway Transmission Gear Pump (Transmission)
C7 On-Highway Engine Fuel Manifold (ARD) - Install
C13 Engine Electronic Unit Injector Sleeve - Install
2006/04/17 New Speed Timing Sensor Available {1912}
2006/06/01 An Improved Speed-Timing Sensor is Now Available {1912}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 736 - FMI 3
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission, SPN 737 - FMI 3