Transmission from Input Transfer Gears and Output Transfer Gears - Separate
分离步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 8S-7640 | 台架 | 1 |
| 8S-7611 | 管 | 1 | |
| 8S-8048 | 鞍座 | 1 | |
| 8S-7615 | 销 | 1 | |
| B | 138-7575 | 连杆支架 | 1 |
| C | 138-7575 | 连杆支架 | 4 |
开始:
- 拆下变速箱、输入分动器和输出分动器。 请参阅拆解和组装, "变速箱、输入分动器和输出分动器 - 拆卸"。
- 将变速箱 (2) 、输入分动器 (1) 和输出分动器 (3) 安置到工具 (A) 上。 变速箱 (2) 、输入分动器 (1) 和输出分动器 (3) 的组合重量约为 2660 kg (5865 lb)。
Show/hide table
 | |
| 图 1 | g01438887 |
- 从输入分动器 (1) 拆卸轭组件 (4) 。
Show/hide table
 | |
| 图 2 | g01438954 |
- 将工具 (B) 和适当的起吊设备固定到输入分动器 (1) 上。 卸下螺栓 (5) 。 将输入分动器 (1) 从变速箱 (2) 分离。 输入分动器 (1) 的重量约为 359 kg (790 lb)。
Show/hide table
 | |
| 图 3 | g01438987 |
- 从输入分动器 (1) 拆卸 O 形密封圈 (6) 。
Show/hide table
 | |
| 图 4 | g01439004 |
- 将工具 (B) 和适当的起吊设备固定到变速箱 (2) 上。 将螺栓 (7) 和变速箱 (2) 从输出分动器 (3) 上拆下。 变速箱 (2) 的重量约为 1225 kg (2700 lb)。 输出分动器 (3) 的重量约为 1080 kg (2375 lb)。
Show/hide table
 | |
| 图 5 | g01439018 |
- 从变速箱 (2) 上卸下 O 形密封圈 (8) 。
Show/hide table
 | |
| 图 6 | g01439120 |
Caterpillar Information System:
992K Wheel Loader and 854K Wheel Dozer Braking System Brake Accumulator
992K Wheel Loader Electrohydraulic System Main Hydraulic System
993K Wheel Loader Braking System Pressure Sensor (Axle Brake Oil)
992K Wheel Loader Electrohydraulic System Relief Valve (Implement Pilot)
992K Wheel Loader Electrohydraulic System Tilt Cylinder
992K Wheel Loader and 854K Wheel Dozer Power Train Final Drive, Brake and Wheel
Bench Test Procedure for a 990, 990 Series II, 990H Wheel Loader and a 844, 844H Wheel Dozer Torque Converter{3101} Bench Test Procedure for a 990, 990 Series II, 990H Wheel Loader and a 844, 844H Wheel Dozer Torque Converter{3101}
993K Wheel Loader Power Train Electronic Control Module
993K Wheel Loader Power Train General Information
2008/09/29 An Improved Three-Piece Oil Pan Gasket is Now Used {1302, 7555}
2008/05/12 Wear that is Acceptable in Specific Gear Pumps {4007, 5073, 5073, 7516}
854K Wheel Dozer and 992K Wheel Loader Power Train Electronic Control Module (ECM) - Replace
854K Wheel Dozer and 992K Wheel Loader Oil Cooler Core (Transmission) - Install
854K Wheel Dozer and 992K Wheel Loader Oil Cooler Core (Engine) - Remove
854K Wheel Dozer and 992K Wheel Loader Oil Cooler Core (Engine) - Install
992K Wheel Loader and 854K Wheel Dozer Power Train Transmission to Input Transfer Gears and Output Transfer Gears - Connect
854K Wheel Dozer and 992K Wheel Loader Battery - Remove and Install
993K Wheel Loader Power Train Input Transfer Gears
994F Wheel Loader Power Train Differential and Bevel Gear (Rear) - Install
994F Wheel Loader Power Train Differential and Bevel Gear (Front) - Install
844K and 854K Wheel Dozers and 990K, 992K, 993K, 994F and 994H Wheel Loaders Powered Access Stairway Connector Locations
992K Wheel Loader and 854K Wheel Dozer Power Train Output Transfer Gears - Disassemble
992K Wheel Loader and 854K Wheel Dozer Braking System Piston Pump (Brake)
993K Wheel Loader Power Train Transmission Hydraulic Control Operation